| *A | for TMMF Made | *B | for TMC Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | - | - |
| *A | w/ Rear Power Window | *B | w/o Rear Power Window |
| *1 | BUTYL TAPE | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
MP grease | - | - |
| *A | w/o Rear Power Window | - | - |
| *1 | WINDOW REGULATOR HANDLE PLATE | *2 | SHAFT SNAP RING |
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
67888D
1.INSTALL REAR DOOR DUST PROOF SEAL (for TMMF Made)
67888D
2.INSTALL REAR DOOR DUST PROOF SEAL (for TMC Made)
|
|
75077
3.INSTALL REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
75874
4.INSTALL QUARTER PANEL WHEEL OPENING MOULDING
67888D
5.INSTALL NO. 2 REAR DOOR WEATHERSTRIP
67872
6.INSTALL REAR DOOR WEATHERSTRIP
68630
7.INSTALL REAR DOOR CHECK ASSEMBLY
| *A | When reusing a bolt. | - | - |
| *a | Bolt A | *b | Bolt B |
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt A.
Apply adhesive to the threads of the bolt A.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly with the bolt A and 2 bolts B.
68230C
10.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION
69204A
11.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
MP grease |
|
Install in this Direction |
Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.
Engage the guides to install the rear door outside handle frame sub-assembly as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
69242G
12.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD
69241G
13.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD
69227L
14.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claws to install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, tighten the screw.
69240
15.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
69318D
16.INSTALL DOOR LOCK WIRING HARNESS SEAL
69060A
17.INSTALL REAR DOOR LOCK ASSEMBLY
69840A
18.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)
|
MP grease | - | - |
Connect the connector.
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the rear door window regulator assembly with the 6 nuts.
Engage the clamp.
69840A
19.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)
|
MP grease | - | - |
Apply MP grease to the sliding parts of the rear door window regulator assembly.
Install the rear door window regulator assembly with the 6 nuts.
Engage the clamp.
67447C
20.INSTALL REAR DOOR WINDOW GUIDE PLATE LOWER
68012
21.INSTALL REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY
|
Install in this Direction | - | - |
68104
22.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
w/ Power Window:
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.
w/ Power Window:
|
Install in this Direction | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly.
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Be careful not to damage the rear door glass sub-assembly.
Install the rear door glass sub-assembly with the 2 bolts.
w/o Power Window:
Install the rear door window regulator handle assembly.
Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.
Remove the rear door window regulator handle assembly.
Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.
Be careful not to damage the rear door glass sub-assembly.
Install the rear door glass sub-assembly with the 2 bolts.
68152C
23.INSTALL REAR DOOR GLASS RUN
67842E
24.INSTALL REAR DOOR SERVICE HOLE COVER
| *a | Reference Point |
|
Butyl Tape |
Apply new butyl tape to the rear door panel.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.
Install the rear door service hole cover according to the reference points on the rear door panel.
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
86160B
25.INSTALL REAR SPEAKER ASSEMBLY
68199
26.INSTALL REAR DOOR BELT REAR SEAL
Install the rear door belt rear seal to the rear door glass inner weatherstrip.
68197A
27.INSTALL REAR DOOR BELT FRONT SEAL
68174A
28.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
Install the rear door glass weatherstrip inner with the rear door rear belt seal and rear door front belt seal.
69284D
29.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
69206C
30.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
67604
31.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
|
Install in this Direction | - | - |
32.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
69260E
33.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)
Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.
Remove the rear door window regulator handle assembly.
Install the window regulator handle plate as shown in the illustration.
Install the rear door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.
34. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
35.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
36.INITIALIZE POWER WINDOW CONTROL SYSTEM
37.INSPECT POWER WINDOW OPERATION