Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2021.07
RM3700E _52 Drivetrain _093735 P910 HYBRID TRANSMISSION / TRANSAXLE _0441812 HYBRID VEHICLE TRANSAXLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442321N02
0.583,1.583 1.323,1.75 0.74,0.167 1.302,0.083 2.083,0.25 0.781,0.167 3.271,0.625 3.406,0.458 3.406,0.458 3.531,0.458 false 1.865,1.063 1.865,0.896 false 0.802,1.083 0.802,0.854 false 0.583,1.667 0.417,1.667 0.417,1.667 0.333,0.875 false 2.344,0.74 2.25,0.167 2.25,0.167 2.083,0.167 false 6,1.323 6.271,1.323 false 4.896,4.083 5.229,4.083 false 1.375,3.688 1.708,3.688 false 1.125,5.167 1.458,5.167 false 1.667,2.583 1.833,2.75 1.833,2.75 2,2.75 false 6.396,0.26 6.729,0.26 false 6.021,4.292 6.021,3.958 false 3.885,0.323 4.167,0.677 0.281,0.354 18 false 5 0.656,1.594 1.469,1.75 0.813,0.156 8 false 43 (438, 32) 1.375,0.094 2.188,0.25 0.813,0.156 8 false 43 (438, 32) 0.396,0.833 0.896,1 0.5,0.167 10 false x2 2.042,1.083 2.323,1.438 0.281,0.354 18 false 3 1.01,1.083 1.292,1.438 0.281,0.354 18 false 3 6.656,1.198 6.938,1.552 0.281,0.354 18 false 4 5.281,3.948 5.563,4.302 0.281,0.354 18 false 2 1.167,3.552 1.448,3.906 0.281,0.354 18 false 6 0.917,5.031 1.198,5.385 0.281,0.354 18 false 7 1.406,3.438 1.74,3.604 0.333,0.167 10 false x2 2.052,2.594 2.333,2.948 0.281,0.354 18 false 8 3.146,0.365 3.646,0.531 0.5,0.167 10 false x2 2.396,0.802 2.896,0.969 0.5,0.167 10 false x2 6.219,0.083 6.5,0.438 0.281,0.354 18 false 1 6.729,3.792 7,3.979 0.271,0.188 10 false x2 5.969,4.302 6.25,4.656 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PERFORM RESOLVER INITIALIZATION - - - (Click here)
2 ENGINE ASSEMBLY WITH TRANSAXLE - - - -
3 ENGINE HANGERS - (Click here) - -
4 ENGINE WIRE 82121 (Click here) - -
5 HV AIR CONDITIONING WIRE 821H2 (Click here) - -
6 STARTER HOLE INSULATOR 28193 - - -
7 FLYWHEEL HOUSING SIDE COVER 11363A - - -
8 NO. 3 WATER BY-PASS HOSE ASSEMBLY 16290F - - -
9 DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY 43409E - - -

C462958N01
1.865,1.083 2.198,1.083 false 5.844,4.177 6.177,4.177 false 2.833,4.76 3.01,5.031 3.01,5.031 3.177,5.031 false 0.969,0.354 1.104,0.354 1.104,0.354 1.375,0.677 false 1.656,0.938 1.938,1.292 0.281,0.354 18 false 9 1.177,2.677 1.458,3.031 0.281,0.354 10 false x5 6.219,4 6.583,4.333 0.365,0.333 18 false 11 3.219,4.854 3.583,5.188 0.365,0.333 18 false 12 2.677,5.25 3.01,5.531 0.333,0.281 10 false x3 0.656,0.208 1.021,0.542 0.365,0.333 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

10 ENGINE ASSEMBLY - (Click here) - -
11 FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY 51201 - - -
12 NO. 2 ENGINE MOVING CONTROL ROD 12364B - - -

C442323N02
4.063,0.344 4.396,0.344 false 4.188,0.958 4.521,0.958 false 4.594,1.667 5.01,1.667 false 1.177,4.833 1.375,4.833 false 2.167,2.75 2.333,2.75 2.333,2.75 2.813,3.802 false 0.823,4.656 1.24,4.99 0.417,0.333 18 false 16 1.365,5.354 1.698,5.604 0.333,0.25 10 false x3 3.594,1.635 3.927,1.885 0.333,0.25 10 false x6 3.292,0.333 3.625,0.583 0.333,0.25 10 false x2 4.708,0.177 5.125,0.51 0.417,0.333 18 false 13 4.958,0.823 5.708,1.156 0.75,0.333 18 false 14 5.365,1.49 5.781,1.823 0.417,0.333 18 false 15 4.823,0.875 5.156,1.125 0.333,0.25 10 false ● 2,2.646 2.177,2.844 0.177,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

13 CONNECTOR COVER 82821T (Click here) - -
14 TERMINAL CAP 82823M (Click here) - -
15 MOTOR CABLE G1148 (Click here) - -
16 MOTOR COOLING COOLER G125A (Click here) - -

● Non-reusable part - -

C442324N02
2.708,1.292 2.875,1.292 2.875,1.292 3.146,1.427 false 5.021,0.688 5.354,0.688 false 5.521,0.979 5.854,0.979 false 4.115,0.958 4.448,0.958 false 5.74,1.365 6.073,1.365 false 6.729,2.51 6.729,2.844 false 2.365,2.594 2.698,2.594 false 2.49,3.677 2.49,4.01 false 0.563,5.063 0.563,5.396 false 1.938,4.802 1.938,5.135 false 2.708,4.833 3,5.083 3,5.083 3.167,5.083 false 2.458,4.833 2.542,5.271 2.542,5.271 2.708,5.271 false 2.385,1.156 2.938,1.51 0.552,0.354 18 false 22 2.229,1.229 2.531,1.417 0.302,0.188 10 false ★ 5.917,0.885 6.469,1.156 0.552,0.271 10 false ● 4.708,0.563 5.26,0.833 0.552,0.271 18 false 23 3.781,0.813 4.333,1.083 0.552,0.271 18 false 24 5.479,1.229 6.031,1.5 0.552,0.271 18 false 21 6.594,2.844 7.01,3.198 0.417,0.354 18 false 21 2.719,2.448 3.271,2.802 0.552,0.354 18 false 20 2.365,4.021 2.917,4.375 0.552,0.354 18 false 19 1.802,5.135 2.354,5.49 0.552,0.354 18 false 17 3.042,5.156 3.594,5.51 0.552,0.354 18 false 25 3.24,4.979 3.792,5.25 0.552,0.271 10 false ● 3.271,1.375 3.521,1.625 0.25,0.25 10 false x2 0.427,5.417 0.979,5.771 0.552,0.354 18 false 18 1.667,5.177 2.219,5.448 0.552,0.271 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

17 NO. 1 MOTOR COOLING PIPE G1251B - - -
18 NO. 2 OIL COOLER TUBE CLAMP 32924E - - -
19 HOSE BRACKET 44781E - - -
20 NO. 1 TRANSMISSION CONTROL CABLE BRACKET 33823 - - -
21 WIRE HARNESS CLAMP BRACKET - - - -
22 STUD BOLT - (Click here) - -
23 TRANSAXLE HOUSING PLUG - - - -
24 TRANSAXLE BREATHER PLUG 30900N - - -
25 UNION - (Click here) - -

● Non-reusable part ★ Precoated part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PERFORM RESOLVER INITIALIZATION

Z101186

NOTICE:

If it is necessary to replace the hybrid vehicle transaxle assembly, make sure to perform resolver initialization before starting work.

Click here(Click here)



Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 4.DISCONNECT ENGINE WIRE

a.
C442325N01
0.354,0 0.74,0.313 0.385,0.313 18 false i 3.948,1.375 4.115,1.667 0.167,0.292 18 true ii 4.875,0.552 5.094,0.844 0.219,0.292 18 true iii 4.646,1.292 4.875,1.552 0.229,0.26 18 true iv 5.75,0.167 5.969,0.458 0.219,0.292 18 true v 6.094,1.042 6.313,1.333 0.219,0.292 18 true vi

i.

Disengage the 6 clamps.


ii.

Disengage the clamp.


iii.

Remove the bolt.


iv.

Disconnect the shift lever position sensor connector.

NOTICE:
C438726

After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.



v.

Disconnect the generator temperature sensor connector.


vi.

Disconnect the resolver (transmission fluid temperature sensor) connector.



Hide 821H2 5.REMOVE HV AIR CONDITIONING WIRE

a.
C442326C02
5.01,2.479 5.385,2.219 true 5.427,2.125 5.677,2.313 0.25,0.188 10 false *a 0.156,0 0.323,0.292 0.167,0.292 18 true i 3.958,0 4.135,0.271 0.177,0.271 18 true ii 1.688,2.073 2,2.344 0.313,0.271 18 true iii
*a Green-colored Lock - -
V100137

Slide - -


i.

Remove the 2 bolts to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.


ii.

Disengage the clamp.


iii.

Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.




Hide 28193 6.REMOVE STARTER HOLE INSULATOR

a.
C429034


Hide 11363A 7.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
C429036


Hide 16290F 8.SEPARATE NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
C429038


Hide 43409E 9.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C432455


Hide 10.REMOVE ENGINE ASSEMBLY

Z101186

NOTICE:
·

To avoid damaging the knock pins, do not pry between the hybrid vehicle transaxle assembly and engine assembly.

·

To prevent the splines of the transmission input damper assembly from becoming misaligned, do not allow the hybrid vehicle transaxle assembly to hit the transmission input damper assembly during engine assembly removal and installation.




a.
C429040


Hide 51201 11.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C442327


Hide 12364B 12.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C442328


Hide 82821T 13.REMOVE CONNECTOR COVER

Z101186

Click here(Click here)

Hide 82823M 14.REMOVE TERMINAL CAP

Z101186

Click here(Click here)

Hide G1148 15.REMOVE MOTOR CABLE

Z101186

Click here(Click here)

Hide G125A 16.REMOVE MOTOR COOLING COOLER

a.
C442329E01
0.385,0 0.563,0.281 0.177,0.281 18 true i 5.667,0.396 5.948,0.677 0.281,0.281 18 true ii 5.188,0.875 5.469,1.156 0.281,0.281 18 true iii 2.063,2.031 2.344,2.313 0.281,0.281 18 true iv

i.

Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.


ii.

Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.


iii.

Disengage the clamp.


iv.

Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.

NOTICE:

Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.




Hide G1251B 17.SEPARATE NO. 1 MOTOR COOLING PIPE

a.
C430378


Hide 32924E 18.REMOVE NO. 2 OIL COOLER TUBE CLAMP

a.
C430379


Hide 44781E 19.REMOVE HOSE BRACKET

a.
C429061


Hide 33823 20.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C429063


Hide 21.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C429065


Hide 22.REMOVE STUD BOLT

a.
C442330N01
0.438,0 0.719,0.354 0.281,0.354 18 false i

i.

Using a E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.



Hide 23.REMOVE TRANSAXLE HOUSING PLUG

Z101186

HINT:

Perform this procedure only when replacement of the transaxle housing plug or gasket is necessary.



a.
C429067


Hide 30900N 24.REMOVE TRANSAXLE BREATHER PLUG

Z101186

HINT:

Perform this procedure only when replacement of the transaxle breather plug is necessary.



a.
C429069


Hide 25.REMOVE UNION

Z101186

HINT:

Perform this procedure only when replacement of the union or O-ring is necessary.



a.
C429071