| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 31 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| *A | for 2WD | *B | for AWD |
| ● | Non-reusable part | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| ● | Non-reusable part | ★ | Precoated part |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
|
|
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.REMOVE FRONT WHEELS
51410
6.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442C
7.REMOVE ENGINE UNDER COVER LH
51441C
8.REMOVE ENGINE UNDER COVER RH
G92A0
13.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY
82662A
14.REMOVE NO. 1 RELAY BLOCK COVER
15.REMOVE ENGINE WIRE
33820B
16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
16571C
17.DISCONNECT NO. 1 RADIATOR HOSE
16572D
18.DISCONNECT NO. 2 RADIATOR HOSE
G922H
19.DISCONNECT INLET HYBRID RADIATOR HOSE
G922F
20.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
23826
21.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
77261D
22.DISCONNECT FUEL TANK TO CANISTER TUBE
16290F
23.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
87245
24.DISCONNECT INLET HEATER WATER HOSE
23901
25.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pump assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
88711
26.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
88704
27.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
45259A
29.REMOVE COLUMN HOLE COVER SILENCER SHEET
32.REMOVE DRIVE SHAFT ASSEMBLY
for TMMF Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for M15A-FXE TMMF Made)>REMOVAL
12318
33.REMOVE ENGINE MOUNTING STAY LH
34.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
1. Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
12353
35.REMOVE ENGINE MOUNTING BRACKET CAP
Turn over the engine mounting bracket cap to the upper part.
While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.
36.INSTALL ENGINE HANGER
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
1. Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
12372A
37.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH
|
|
G92A0A
38.DISCONNECT INVERTER RESERVE TANK ASSEMBLY
12305
39.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
|
|
28193
40.REMOVE STARTER HOLE INSULATOR
11363A
41.REMOVE FLYWHEEL HOUSING SIDE COVER
821H2
42.REMOVE HV AIR CONDITIONING WIRE
82121
43.REMOVE ENGINE WIRE
44.REMOVE WATER HOSE
19315
48.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
50.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
51.REMOVE ENGINE HANGER