|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with SST | ● | Non-reusable part |
|
Toyota Genuine ATF WS |
|
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | MOTOR COOLING COOLER | G125A | ( )
|
- | - |
| 12 | MOTOR CABLE | G1148 | ( )
|
- | - |
| 13 | TERMINAL CAP | 82823M | ( )
|
- | - |
| 14 | CONNECTOR COVER | 82821T | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 15 | NO. 2 ENGINE MOVING CONTROL ROD | 12364B | ( )
|
- | - |
| 16 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | 51201 | - | - | - |
| 17 | ENGINE ASSEMBLY | - | ( )
|
- | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
1.INSTALL UNION
|
|
|
Toyota Genuine ATF WS | - | - |
Coat a new O-ring with ATF.
Install the union and O-ring to the hybrid vehicle transaxle assembly.
30900N
2.INSTALL TRANSAXLE BREATHER PLUG
|
|
3.INSTALL TRANSAXLE HOUSING PLUG
|
|
4.INSTALL STUD BOLT
Apply adhesive to 2 or 3 threads on the ends of the 2 stud bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
In order to ensure proper sealing of the 2 stud bolts, install them within 10 minutes of applying adhesive.
Using a E8 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.
Clean and degrease the 2 stud bolt holes of the hybrid vehicle transaxle assembly.
5.INSTALL WIRE HARNESS CLAMP BRACKET
33823
6.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
44781E
7.INSTALL HOSE BRACKET
G1251B
8.TEMPORARILY INSTALL NO. 1 MOTOR COOLING PIPE
32924E
9.INSTALL NO. 2 OIL COOLER TUBE CLAMP
G1251B
10.FULLY TIGHTEN NO. 1 MOTOR COOLING PIPE
| *a | Torque Wrench Fulcrum Length | - | - |
Using a 17 mm union nut wrench, tighten the flare nut to install the No. 1 motor cooling pipe.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):
29.4 N*m (300 kgf*cm, 22 ft.*lbf)
G125A
11.INSTALL MOTOR COOLING COOLER
| *a | Temporarily Tighten | *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark | - | - |
Temporarily install the motor cooling cooler with No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the 3 bolts.
Tighten the 3 bolts in the order shown in the illustration.
Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.
Engage the clamp.
Tighten the oil cooler union bolt to install the No. 2 motor cooling pipe.
Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.
Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.
12364B
15.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten | - | - |
Install the No. 2 engine moving control rod to the hybrid vehicle transaxle assembly with the 3 bolts in the order shown in the illustration.
51201
16.TEMPORARILY INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
17.INSTALL ENGINE ASSEMBLY
| *1 | Knock Pin | - | - |
Make sure that the knock pins are installed to the engine assembly.
Install the engine assembly to the hybrid vehicle transaxle assembly with the 7 bolts.
| Bolt | Bolt Length | Torque |
|---|---|---|
| (A), (C) | 45 mm (1.77 in.) | 46 N*m (469 kgf*cm, 34 ft.*lbf) |
| (B) | 35 mm (1.38 in.) | 25 N*m (255 kgf*cm, 18 ft.*lbf) |
When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.
Temporarily tighten the bolt (A), and then fully tighten the 7 bolts in the order of (B), (A) and (C).
Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not use excessive force when installing the engine assembly.
Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.
When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the engine assembly.
When installing the engine assembly to the hybrid vehicle transaxle assembly, make sure to securely fit the knock pins into the knock pin holes.
43409E
18.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
| *a | Temporarily Tighten | - | - |
Temporarily install the drive shaft insulator sub-assembly to the cylinder block sub-assembly and hybrid vehicle transaxle assembly with the 2 bolts.
Tighten the 2 bolts in the order shown in the illustration.
16290F
19.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY
11363A
20.INSTALL FLYWHEEL HOUSING SIDE COVER
28193
21.INSTALL STARTER HOLE INSULATOR
821H2
22.INSTALL HV AIR CONDITIONING WIRE
| *a | Green-colored Lock | - | - |
|
Slide | - | - |
Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.
Make sure to wear insulated gloves.
Make sure that the connector is connected securely.
Engage the clamp.
Install the HV air conditioning wire to the hybrid vehicle transaxle assembly with the 2 bolts.
82121
23.CONNECT ENGINE WIRE
Connect the resolver (transmission fluid temperature sensor) connector.
Connect the generator temperature sensor connector.
Confirm that no foreign matter or water has entered the connector of the shift lever position sensor and connect the connector.
Engage the clamp.
Install the bolt.
Engage the 6 clamps.
24.REMOVE ENGINE HANGER
25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE