| *A | for HV Model | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | REAR FLEXIBLE HOSE | 47319F | - | - | - |
| 10 | REAR DISC BRAKE CYLINDER ASSEMBLY | 47850 | - | - | - |
| 11 | REAR DISC BRAKE PAD | 04466 | - | - | - |
| 12 | REAR DISC BRAKE ANTI-SQUEAL SHIM KIT | 04946 | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| *1 | NO. 1 REAR DISC BRAKE CYLINDER SLIDE BUSH | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC (C13CD00, C13CE00, C140000) may be stored. As there is no malfunction, clear the DTC. (for HV Model)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION (for HV Model)
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
for HV Model: Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.
for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made)>PRECAUTION
for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made)>PRECAUTION
2.REMOVE REAR WHEEL
3.PERFORM REAR BRAKE PAD REPLACEMENT MODE
for HV Model:
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made)>UTILITY
for Gasoline Model:
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE
5.DRAIN BRAKE FLUID
|
|
47319F
9.SEPARATE REAR FLEXIBLE HOSE
47850
10.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY
04466
11.REMOVE REAR DISC BRAKE PAD
13.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE
|
|
14.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN
Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.
Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.
Do not damage the rear No. 2 disc brake cylinder slide pin.
47775B
15.REMOVE NO. 1 BUSH DUST BOOT
47822
16.REMOVE REAR DISC BRAKE CYLINDER MOUNTING
42431
17.REMOVE REAR DISC
| *a | Matchmark | - | - |
Put matchmarks on the rear disc and rear axle hub and bearing assembly.
Remove the rear disc.