Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486937 LIGHTING SYSTEM(w/ Adaptive High Beam System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Adaptive High Beam System)  Back-up Light Circuit  


DESCRIPTION

The hybrid vehicle control ECU controls the back-up lights via the BKUP LP relay.

WIRING DIAGRAM

for LHD


E472180E01
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.167,3.698 3.396,4.135 2.229,0.438 10 false Rear Light Assembly RH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 1.625,3.729 0.458,0.198 10 false Y14 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.24,3.042 0.458,0.198 10 false 6 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1


for RHD


E472180E02
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.167,3.698 3.396,4.135 2.229,0.438 10 false Rear Light Assembly LH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 1.625,3.729 0.458,0.198 10 false Y12 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.24,3.042 0.458,0.198 10 false 6 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

When replacing the hybrid vehicle control ECU, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.READ VALUE USING GTS
a.

Turn the ignition switch to ON.


b.

Move the shift lever to R.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse shut off status OFF or ON OFF: Fuse has no shut off history
ON: Fuse has shut off history
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.READ VALUE USING GTS

B

10.CHECK REAR LIGHT ASSEMBLY RH

C

12.CHECK REAR LIGHT ASSEMBLY LH
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Back-up Light Input Signal Back-up light input OFF or ON OFF: Shift lever in any position other than R
ON: Shift lever in R
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Input Signal
50003 475 1305
OK:

Display changes according to shift lever operation.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - POWER DISTRIBUTION BOX ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4G power distribution box assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4G-1 - Body ground Ignition switch off 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Y14 rear light assembly RH connector.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Y14-6 (B) - 4E-38 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Y14-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Y12 rear light assembly LH connector.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Y12-6 (B) - 4E-38 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Y12-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the 4B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-49 (BL) - 4B-29 Always Below 1 Ω
H44-49 (BL) or 4B-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HYBRID VEHICLE CONTROL ECU (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU (OUTPUT VOLTAGE)
E438259C01
0.938,1.677 1.208,1.938 0.271,0.26 0.99,1.719 1.302,1.917 0.313,0.198 10 false 4B 0.458,0.208 0.771,0.406 0.313,0.198 10 false *a
*a Component with harness connected
(Power Distribution Box Assembly)


a.

Connect the H44 hybrid vehicle control ECU connector.


b.

Connect the 4B power distribution box assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-29 - Body ground Ignition switch ON, reverse (R) not selected Below 1 V
4B-29 - Body ground Ignition switch ON, reverse (R) selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

10.CHECK REAR LIGHT ASSEMBLY RH
a.

Disconnect the Y14 rear light assembly RH connector.


b.

Turn the ignition switch to ON.


c.

Move the shift lever to R.


d.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse shut off status OFF or ON OFF: Fuse has no shut off history
ON: Fuse has shut off history
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

11.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Y14-6 (B) or 4E-38 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK REAR LIGHT ASSEMBLY LH
a.

Disconnect the Y12 rear light assembly LH connector.


b.

Turn the ignition switch to ON.


c.

Move the shift lever to R.


d.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse shut off status OFF or ON OFF: Fuse has no shut off history
ON: Fuse has shut off history
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

13.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Y12-6 (B) or 4E-38 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR