for LED Headlight:
When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the light control LED ECU and illuminates the daytime running lights.
for Halogen Headlight:
When the main body ECU (multiplex network body ECU) receives the light control switch position signal, it sends an illumination request signal to the semiconductor power integration ECU and illuminates the daytime running lights.
for LED Headlight
for Halogen Headlight
HEADLIGHT ASSEMBLY CIRCUIT (for LED Headlight)
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
*1: w/ Entry and Start System
Using the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime running lights | OFF or ON | - |
| Tester Display |
|---|
| Daytime Running Light |
Clearance lights and daytime running lights illuminate.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (LH side daytime running light does not illuminate.) | B |
| NG (RH side daytime running light does not illuminate.) | C |
A
B
C
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Headlight | A |
| for Halogen Headlight | B |
A
B
Interchange the daytime running light assembly LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the daytime running lights.
The daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the light control LED ECU LH with RH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check that the daytime running light operates normally.
Daytime running light operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Headlight Housing Sub-assembly (Wire Harness)) |
*b | Component without harness connected
(to Light Control LED ECU) |
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Remove the headlight housing sub-assembly (wire harness).
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4)Location & Routingewd_type=routing;type=c;code=A4 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=5 |
||
| A4-5(PWM) - B-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A4 headlight assembly LH connector.
Disconnect the B12 daytime running light assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4,B12)Location & Routingewd_type=routing;type=c,c;code=A4,B12 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=3 Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LHewd_type=component;type=c;code=B12;pinno=2 |
||
| A4-3(DRL) - B12-2(DRLC) | Always | Below 1 Ω |
| A4-3(DRL) - Body ground | Always | 10 kΩ or higher |
| B12-2(DRLC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4,B12)Location & Routingewd_type=routing;type=c,c;code=A4,B12 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=5 Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LHewd_type=component;type=c;code=B12;pinno=1 |
||
| A4-5(E) - Body ground | Always | Below 1 Ω |
| B12-1(E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A4,B12)Location & Routingewd_type=routing;type=c,c;code=A4,B12 Click Connector(A4)Engine Compartment>Engine Room Main Wire>Headlight Assembly LHewd_type=component;type=c;code=A4;pinno=2 Click Connector(B12)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LHewd_type=component;type=c;code=B12;pinno=2 |
||
| A4-2(LO) - Body ground | Always | 11 to 14 V |
| B12-2(B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the daytime running light assembly LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the daytime running lights.
The daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B10)Location & Routingewd_type=routing;type=c;code=B10 Click Connector(B10)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LHewd_type=component;type=c;code=B10;pinno=1 |
||
| B10-1(E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B10)Location & Routingewd_type=routing;type=c;code=B10 Click Connector(B10)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly LHewd_type=component;type=c;code=B10;pinno=2 |
||
| B10-2(B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Headlight | A |
| for Halogen Headlight | B |
A
B
Interchange the daytime running light assembly RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the daytime running lights.
The daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the light control LED ECU RH with LH and connect the connectors to them.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check that the daytime running light operates normally.
Daytime running light operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Headlight Housing Sub-assembly (Wire Harness)) |
*b | Component without harness connected
(to Light Control LED ECU) |
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Remove the headlight housing sub-assembly (wire harness).
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5)Location & Routingewd_type=routing;type=c;code=A5 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=5 |
||
| A5-5(PWM) - B-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 headlight assembly RH connector.
Disconnect the B13 daytime running light assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5,B13)Location & Routingewd_type=routing;type=c,c;code=A5,B13 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=3 Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RHewd_type=component;type=c;code=B13;pinno=2 |
||
| A5-3(DRL) - B13-2(DRLC) | Always | Below 1 Ω |
| A5-3(DRL) - Body ground | Always | 10 kΩ or higher |
| B13-2(DRLC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5,B13)Location & Routingewd_type=routing;type=c,c;code=A5,B13 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=5 Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RHewd_type=component;type=c;code=B13;pinno=1 |
||
| A5-5(E) - Body ground | Always | Below 1 Ω |
| B13-1(E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A5,B13)Location & Routingewd_type=routing;type=c,c;code=A5,B13 Click Connector(A5)Engine Compartment>Engine Room Main Wire>Headlight Assembly RHewd_type=component;type=c;code=A5;pinno=2 Click Connector(B13)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RHewd_type=component;type=c;code=B13;pinno=2 |
||
| A5-2(LO) - Body ground | Always | 11 to 14 V |
| B13-2(B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the daytime running light assembly RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>DAYTIME RUNNING LIGHT ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the daytime running lights.
The daytime running lights operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B11)Location & Routingewd_type=routing;type=c;code=B11 Click Connector(B11)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RHewd_type=component;type=c;code=B11;pinno=1 |
||
| B11-1(E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(B11)Location & Routingewd_type=routing;type=c;code=B11 Click Connector(B11)Engine Compartment>No. 3 Engine Room Wire>Daytime Running Light Assembly RHewd_type=component;type=c;code=B11;pinno=2 |
||
| B11-2(B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG