Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486938 LIGHTING SYSTEM(w/o Adaptive High Beam System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Adaptive High Beam System)  Back-up Light Circuit  


DESCRIPTION

The hybrid vehicle control ECU controls the back-up lights via the BKUP LP relay.

WIRING DIAGRAM

for RHD


E472180E09
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.167,3.698 3.396,4.135 2.229,0.438 10 false Rear Light Assembly LH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 2.354,3.729 1.188,0.198 10 false Y12 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.417,3.104 0.635,0.26 10 false 6 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1 0.167,0.083 2.521,0.417 2.354,0.333 12 false for LED Type Back-up Light:

E472180E10
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.167,3.698 3.396,4.135 2.229,0.438 10 false Rear Light Assembly RH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 2.813,3.854 1.646,0.323 10 false Y16 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.479,3.219 0.698,0.375 10 false 1 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1 0.146,0.094 2.677,0.479 2.531,0.385 12 false for Bulb Type Back-up Light:


for LHD


E472180E07
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.167,3.698 3.396,4.135 2.229,0.438 10 false Rear Light Assembly RH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 2.813,3.854 1.646,0.323 10 false Y14 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.479,3.219 0.698,0.375 10 false 6 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1 0.125,0.104 2.573,0.49 2.448,0.385 12 false for LED Type Back-up Light:

E472180E08
6.208,0.833 6.646,1.26 0.438,0.427 10 false IC 0.563,1.969 1.448,2.417 0.885,0.448 10 false from Auxiliary Battery 4.833,2.635 5.906,2.833 1.073,0.198 10 false BKUP LP 0.813,1.417 3.646,1.667 2.833,0.25 10 false Hybrid Vehicle Control ECU 1.563,3.125 3.427,3.385 1.865,0.26 10 false Back-up Light 1.156,3.698 3.385,4.135 2.229,0.438 10 false Rear Light Assembly LH 4.427,4.948 6.583,5.167 2.156,0.219 10 false Power Distribution Box Assembly 1.208,2.854 1.365,3.052 0.156,0.198 10 false E 2.552,2.854 3.01,3.052 0.458,0.198 10 false B 1.969,0.875 2.427,1.073 0.458,0.198 10 false BL 2.26,2.156 3.938,2.427 1.677,0.271 10 false INP STD NO. 1-1 1.167,3.531 2.354,3.729 1.188,0.198 10 false Y33 2.25,0.76 2.708,0.958 0.458,0.198 10 false 49 3.573,0.667 4.031,0.865 0.458,0.198 10 false 29 3.583,0.854 4.042,1.052 0.458,0.198 10 false 4B 3.583,1.979 4.042,2.177 0.458,0.198 10 false 4G 3.583,2.969 4.042,3.167 0.458,0.198 10 false 4E 1,2.844 1.458,3.042 0.458,0.198 10 false 2 3.573,2.781 4.031,2.979 0.458,0.198 10 false 38 2.781,2.844 3.417,3.104 0.635,0.26 10 false 1 0.802,1.25 1.26,1.448 0.458,0.198 10 false H44 3.615,1.792 4.073,1.99 0.458,0.198 10 false 1 0.115,0.104 2.531,0.469 2.417,0.365 12 false for Bulb Type Back-up Light:


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.*1

*1: w/ Entry and Start System




PROCEDURE

1.READ VALUE USING GTS
a.

Turn the ignition switch to ON.


b.

Changes the shift lever R position.


c.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse condition OFF or ON OFF: Back-up light fuse not shut off
ON: Back-up light fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

2.READ VALUE USING GTS

B

9.INSPECT REAR LIGHT ASSEMBLY

C

11.INSPECT REAR LIGHT ASSEMBLY
2.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical > Power Distribution Box > Data List.


b.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Input Signal Back-up light input OFF or ON OFF: Back-up light is not input
ON: Back-up light is input
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Input Signal
50003 475 1305
OK:

Display changes according to shift lever operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

7.CHECK HYBRID VEHICLE CONTROL ECU (OUTPUT VOLTAGE)
3.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical > Power Distribution Box > Data List.


b.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Output Signal Back-up light output OFF or ON OFF: Back-up light is not output
ON: Back-up light is output
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Output Signal
50003 475 1306
OK:

Display changes according to shift lever operation.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4G power distribution box assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4G-1 - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Y12*1 or Y16*2 rear light assembly connector.

*1: for LED Type Back-up Light

*2: for Blub Type Back-up Light



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the 4E power distribution box assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12,Y16)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(Y16)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Y12-6 (B) - Body ground*1 Always 10 kΩ or higher
Y16-1 (B) - Body ground*2 Always 10 kΩ or higher
4E-38 - Body ground Always 10 kΩ or higher


*1: for LED Type Back-up Light

*2: for Blub Type Back-up Light



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the Y14*1 or Y33*2 rear light assembly connector.

*1: for LED Type Back-up Light

*2: for Blub Type Back-up Light



b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the 4E power distribution box assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14,Y33)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(Y33)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Y14-6 (B) - Body ground*1 Always 10 kΩ or higher
Y33-1 (B) - Body ground*2 Always 10 kΩ or higher
4E-38 - Body ground Always 10 kΩ or higher


*1: for LED Type Back-up Light

*2: for Blub Type Back-up Light



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HYBRID VEHICLE CONTROL ECU (OUTPUT VOLTAGE)
a.
E438259C03
0.938,1.677 1.208,1.938 0.271,0.26 0.99,1.719 1.302,1.917 0.313,0.198 10 false 4B 0.458,0.208 0.771,0.406 0.313,0.198 10 false *a
*a Component with harness connected
(Power Distribution Box Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4B-29 - Body ground Ignition switch ON, shift lever except R position Below 1 V
4B-29 - Body ground Ignition switch ON, shift lever R position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - POWER DISTRIBUTION BOX ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the 4B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-49 (BL) - 4B-29 Always Below 1 Ω
H44-49 (BL) - Body ground Always 10 kΩ or higher
4B-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR LIGHT ASSEMBLY
a.

Disconnect the Y12*1 or Y16*2 rear light assembly connector.

*1: for LED Type Back-up Light

*2: for Bulb Type Back-up Light



b.

Turn the ignition switch to ON.


c.

Changes the shift lever except R position.


d.

Changes the shift lever R position.


e.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse condition OFF or ON OFF: Back-up light fuse not shut off
ON: Back-up light fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

10.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y12,Y16)Location & Routing

Click Connector(Y12)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Click Connector(Y16)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Y12-6 (B) - Body ground*1 Always 10 kΩ or higher
Y16-1 (B) - Body ground*2 Always 10 kΩ or higher
4E-38 - Body ground Always 10 kΩ or higher


*1: for LED Type Back-up Light

*2: for Bulb Type Back-up Light



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT REAR LIGHT ASSEMBLY
a.

Disconnect the Y14*1 or Y33*2 rear light assembly connector.

*1: for LED Type Back-up Light

*2: for Bulb Type Back-up Light



b.

Turn the ignition switch to ON.


c.

Changes the shift lever except R position.


d.

Changes the shift lever R position.


e.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Back-up Light Fuse Shut Off Status Back-up light fuse condition OFF or ON OFF: Back-up light fuse not shut off
ON: Back-up light fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Back-up Light Fuse Shut Off Status
50003 475 1308
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y14,Y33)Location & Routing

Click Connector(Y14)Body>No. 2 Back Door Wire>Rear Light Assembly RH

Click Connector(Y33)Body>No. 2 Back Door Wire>Rear Light Assembly LH

Y14-6 (B) - Body ground*1 Always 10 kΩ or higher
Y33-1 (B) - Body ground*2 Always 10 kΩ or higher
4E-38 - Body ground Always 10 kΩ or higher


*1: for LED Type Back-up Light

*2: for Bulb Type Back-up Light



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR