Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › ENGINE COOLANT TEMPERATURE SENSOR › from 2021.07
RM3700E _51 Engine / Hybrid System _093768 M15A-FXE ENGINE CONTROL _0442041 ENGINE COOLANT TEMPERATURE SENSOR A

M15A-FXE ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A476123N01
6.5,0.229 6.833,0.229 false 3.969,0.76 4.385,0.76 false 1.948,0.76 2.281,0.76 false 4.667,4.354 5,4.354 false 4.135,0.594 4.552,0.313 4.552,0.313 4.698,0.313 false 5.094,4.167 5.375,4.521 0.281,0.354 18 false 1 6.26,0.094 6.542,0.448 0.281,0.354 18 false 2 1.75,0.604 2.031,0.958 0.281,0.354 18 false 3 4.771,0.604 5.052,0.958 0.281,0.354 18 false 4 4.792,0.26 5.063,0.563 0.271,0.302 10 false ● 3.156,5.198 3.427,5.5 0.271,0.302 10 false x4 3.885,5.375 4.156,5.677 0.271,0.302 10 false x4 4.552,5.198 4.823,5.5 0.271,0.302 10 false x9

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
2 DRAIN ENGINE COOLANT - - (Click here) -
3 HYBRID MOTOR CONTROL INVERTER ASSEMBLY G92A0 - - -
4 ENGINE COOLANT TEMPERATURE SENSOR 89422A (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine coolant temperature sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of engine coolant temperature sensor Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide G92A0 3.REMOVE HYBRID MOTOR CONTROL INVERTER ASSEMBLY

Hide 89422A 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Z101186

NOTICE:

If the engine coolant temperature sensor has been struck or dropped, replace it.



a.
A458733N01
0.583,0.083 0.781,0.375 0.198,0.292 18 true i 4.094,0.094 4.292,0.385 0.198,0.292 18 true ii