Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0442661 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB411  Outer Mirror Indicator (Module "B" Side) Circuit Short to Ground  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (B) detects a short to ground in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB411 Outer Mirror Indicator (Module "B" Side) Circuit Short to Ground
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH (B)


Blind Spot Monitor "B" A

WIRING DIAGRAM

w/ Panoramic View Monitor System


E270468E69
3.073,1.458 3.229,1.656 0.156,0.198 10 false 2 3.094,1.896 3.365,2.104 0.271,0.208 10 false 1 2.813,1.625 2.969,1.823 0.156,0.198 10 false + 2.802,2.021 2.958,2.219 0.156,0.198 10 false - 1.146,2.365 1.802,2.594 0.656,0.229 10 false B 1.135,2.521 3.594,2.865 2.458,0.344 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.448,3.729 2.927,4.021 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 5.406,1.594 5.875,1.792 0.469,0.198 10 false OMIL 5.25,1.49 5.719,1.688 0.469,0.198 10 false 4 5.313,3.563 5.781,3.76 0.469,0.198 10 false T6 5.313,3.75 6.521,4.365 1.208,0.615 10 false Blind Spot Monitor Sensor LH (B) 0.458,3.552 0.875,3.74 0.417,0.188 10 false L8 3.427,1.458 3.823,1.625 0.396,0.167 10 false BSL+ 3.646,1.896 3.906,2.083 0.26,0.188 10 false - 3.896,1.458 4.135,1.656 0.24,0.198 10 false 8 3.875,1.896 4.167,2.083 0.292,0.188 10 false 15


w/o Panoramic View Monitor System


E270468E82
3.073,1.458 3.229,1.656 0.156,0.198 10 false 2 3.094,1.896 3.365,2.104 0.271,0.208 10 false 1 2.813,1.625 2.969,1.823 0.156,0.198 10 false + 2.802,2.021 2.958,2.219 0.156,0.198 10 false - 1.146,2.365 1.802,2.594 0.656,0.229 10 false D 1.135,2.521 3.594,2.865 2.458,0.344 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.448,3.729 2.927,4.021 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 5.406,1.594 5.875,1.792 0.469,0.198 10 false OMIL 5.25,1.49 5.719,1.688 0.469,0.198 10 false 4 5.313,3.563 5.781,3.76 0.469,0.198 10 false T6 5.313,3.75 6.521,4.365 1.208,0.615 10 false Blind Spot Monitor Sensor LH (B) 0.458,3.552 0.875,3.74 0.417,0.188 10 false L12 3.427,1.458 3.823,1.625 0.396,0.167 10 false BSL+ 3.646,1.896 3.906,2.083 0.26,0.188 10 false - 3.896,1.458 4.135,1.656 0.24,0.198 10 false 1 3.875,1.896 4.167,2.083 0.292,0.188 10 false 11


CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Panoramic View Monitor System A
w/o Panoramic View Monitor System B



A

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - OUTER REAR VIEW MIRROR ASSEMBLY LH)

B

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - OUTER REAR VIEW MIRROR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


b.

Disconnect the L8 outer rear view mirror assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T6)Location & Routing

Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LH

T6-4 (OMIL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the B outer mirror LH (outer rear view mirror indicator LH) connector.


Procedure1

a.
E395851C28
1.396,0.156 1.802,0.438 0.406,0.281 2.677,1.469 2.302,1.188 true 1.5,0.208 1.74,0.385 0.24,0.177 10 false L8 2.729,1.417 3.229,1.615 0.5,0.198 10 false BSL+ 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L8)Location & Routing

Click Connector(L8)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L8-8 (BSL+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

OK

NG

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - OUTER REAR VIEW MIRROR ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the T6 blind spot monitor sensor LH (B) connector.


b.

Disconnect the L12 outer rear view mirror assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T6)Location & Routing

Click Connector(T6)Body>No. 8 Floor Wire>Blind Spot Monitor Sensor LH

T6-4 (OMIL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

Pre-procedure1

a.

Disconnect the D outer mirror LH (outer rear view mirror indicator LH) connector.


Procedure1

a.
E434433C06
1.396,0.156 1.833,0.448 0.438,0.292 0.583,1.635 1,1.365 true 1.5,0.208 1.792,0.396 0.292,0.188 10 false L12 0.177,1.573 0.677,1.771 0.5,0.198 10 false BSL+ 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L12)Location & Routing

Click Connector(L12)Body>Front Door Wire LH / Television Camera Wire>Outer Rear View Mirror Assembly LH

L12-1 (BSL+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

8.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

OK

NG

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)