Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › from 2021.07
RM3700E _53 Suspension _093739 REAR SUSPENSION _0441856 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C449855N02
2.385,4.438 3.052,4.604 0.667,0.167 2.344,4.396 3.094,4.646 0.75,0.25 4.25,4.552 4.698,5.198 0.448,0.646 0.083,0.833 1.167,1.167 1.083,0.333 0.042,0.792 1.208,1.208 1.167,0.417 1.5,0.583 1.719,0.583 false 1.458,1.635 1.75,1.635 false 1.99,1.833 2.354,1.833 false 4.115,1.375 4.531,1.375 false 4.042,2.531 4.906,2.531 false 5.083,3.458 5.583,3.458 false 3.063,4.51 3.563,4.51 false 6.49,0.323 6.74,0.323 false 6.542,0.75 6.792,0.75 false 1.167,1 1.333,1 1.333,1 1.823,1.292 false 1.281,0.417 1.563,0.771 0.281,0.354 18 false 5 1.219,1.438 1.5,1.792 0.281,0.354 18 false 4 2.688,1.646 2.969,2 0.281,0.354 18 false 3 4.552,1.25 4.833,1.604 0.281,0.354 18 false 1 5.271,2.344 5.917,2.75 0.646,0.406 18 false 2, 8 4.844,3.292 5.052,3.594 0.208,0.302 18 false 6 2.396,4.427 3.125,4.708 0.729,0.281 8 false 49 (500, 36) 5.813,0.156 6.74,0.49 0.927,0.333 18 false 9, 10 6.333,0.604 6.542,0.906 0.208,0.302 18 false 7 4.271,4.563 4.542,4.875 0.271,0.313 12 false *A 0.26,0.844 0.927,1.021 0.667,0.177 8 false 15 (153, 11) 0.167,1.01 1.25,1.177 1.083,0.167 8 false 6.7 (68, 59 in.*lbf)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR SUSPENSION SUPPORT ASSEMBLY 48760B - - -
2 TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
3 REAR SUSPENSION SUPPORT 48755 (Click here) - -
4 REAR SHOCK ABSORBER CUSHION RETAINER 48597A (Click here) - -
5 DECK SIDE TRIM COVER 64715C - - -
6 REAR WHEEL - - - -
7 STABILIZE SUSPENSION - (Click here) - -
8 FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
9 INSPECT REAR WHEEL ALIGNMENT - - - (Click here)
10 PERFORM INITIALIZATION - - - (Click here)

*A for 2WD - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with SST

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side

·

The following procedure is for the LH side.



PROCEDURE

Hide 48760B 1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

Hide 48540 2.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.

for 2WD:

C443642N02
0.406,0.063 0.688,0.417 0.281,0.354 18 false i

i.

Insert the upper end of the rear shock absorber assembly with rear suspension support assembly into the vehicle body, temporarily install the rear shock absorber assembly to the rear axle beam assembly with the bolt and nut.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




b.

for AWD:

C443643N01
1.906,0.031 2.188,0.385 0.281,0.354 18 false i

i.

Insert the upper end of the rear shock absorber assembly with rear suspension support assembly into the vehicle body, temporarily install the rear shock absorber assembly to the rear No. 1 suspension arm assembly with the bolt.



Hide 48755 3.INSTALL REAR SUSPENSION SUPPORT

a.
C429394C02
2.646,0.333 2.958,0.531 0.313,0.198 10 false *a 4.365,0.333 4.677,0.531 0.313,0.198 10 false *b 0.406,0.094 0.802,0.5 0.396,0.406 18 false i
*a Correct *b Incorrect


i.

Install the rear suspension support to the rear shock absorber assembly.

NOTICE:

Make sure that the rear suspension support is correctly installed as shown in the illustration.




Hide 48597A 4.INSTALL REAR SHOCK ABSORBER CUSHION RETAINER

a.
C484093C01
4.979,3.094 5.146,2.938 true 4.677,3.073 4.552,2.906 true 5.313,1.896 5.594,2.281 true 0.292,0.094 0.573,0.448 0.281,0.354 18 true i 3.74,0.083 4.146,0.396 0.406,0.313 18 true ii 4.406,2.792 4.719,2.99 0.313,0.198 10 false *b 5.146,2.813 5.458,3.01 0.313,0.198 10 false *c 5.458,0.688 5.771,0.885 0.313,0.198 10 false *a 5.51,2.302 5.969,2.5 0.458,0.198 10 true SST 6.406,2.292 6.719,2.49 0.313,0.198 10 true *d 4.052,2.167 4.365,2.365 0.313,0.198 10 true *e
*a Torque Wrench Fulcrum Length *b Rear Shock Absorber Cushion Retainer
*c Collar *d Turn
*e Hold - -


i.

Install the rear shock absorber cushion retainer to the rear shock absorber assembly


ii.

While using a 5 mm hexagon socket wrench to hold the rear shock absorber assembly in place, use a SST to tighten the nut until the rear shock absorber cushion retainer is seated to the collar of the rear suspension support assembly.

SST
09729-00140  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a SST(fulcrum length of 200 mm (7.87 in.))+ torque wrench (fulcrum length of 162 mm (6.38 in.))) : 6.7 N*m (68 kgf*cm,59 in.*lbf))





Hide 64715C 5.INSTALL DECK SIDE TRIM COVER

Hide 6.INSTALL REAR WHEEL

Hide 7. STABILIZE SUSPENSION

Z101186

Click here(Click here)

Hide 48540 8.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.

for 2WD:

C443642N03
0.406,0.083 0.688,0.438 0.281,0.354 18 false i

i.

Fully tighten the rear shock absorber assembly (lower side) with the bolt while keeping the nut from rotating.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




b.

for AWD:

C443643

i.

Fully tighten the rear shock absorber assembly (lower side) with the bolt.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)



Hide 10.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)
Panoramic view monitor system w/o Advanced Park:
(Click here)
w/ Advanced Park:
(Click here)
w/ Advanced Park:
Advanced Park
(Click here)