| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE | - | - | - | - |
| 2 | ECM | 89661 | - | - | - |
| 3 | NO. 1 RELAY BLOCK COVER | 82662A | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | NO. 1 IGNITION RELAY | 28371 | - | - | - |
| 5 | WINDSHIELD WIPER RELAY | 85948 | - | - | - |
| 6 | VVT RELAY | 85912K | - | - | - |
| 7 | SECURITY WARNING RELAY | 89730A | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | RELAY BLOCK LOWER COVER | 82663 | ( )
|
- | - |
| 9 | FUSE BLOCK ASSEMBLY | 82610A | ( )
|
- | - |
| 10 | ENGINE ROOM FUSIBLE LINK | 82210P | - | - | - |
| *A | for RHD | - | - |
| *1 | WIRE HARNESS | *2 | ENGINE ROOM RELAY BLOCK |
| *3 | WIRE HARNESS REPAIR TAPE | - | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the engine room fusible link removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
89661
2.REMOVE ECM
82662A
3.REMOVE NO. 1 RELAY BLOCK COVER
28371
4.REMOVE NO. 1 IGNITION RELAY
85948
5.REMOVE WINDSHIELD WIPER RELAY
85912K
6.REMOVE VVT RELAY
89730A
7.REMOVE SECURITY WARNING RELAY
82663
8.REMOVE RELAY BLOCK LOWER COVER
Remove the nut.
Disconnect the 2 connectors.
|
Separate in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.
for RHD:
1. Disengage the clamps.
Remove the 2 bolts and nut.
| *1 | Engine Room Relay Block Assembly | - | - |
Disengage the guides to separate the engine room relay block assembly.
Disengage the clamp to separate the wire harness.
Apply protective tape to the engine room relay block as shown in the illustration.
Remove the wire harness repair tapes.
Disengage the claws to separate the relay block lower cover.
Using a screwdriver with its tip wrapped in protective tape, disengage the claws to remove the relay block lower cover.
82610A
9.SEPARATE FUSE BLOCK ASSEMBLY
|
Separate in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.
Remove the vinyl tape.
|
Move in this Direction | - | - |
Move the engine room relay block as shown in the illustration.
|
Separate in this Direction | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the fuse block assembly as shown in the illustration.
82210P
10.REMOVE ENGINE ROOM FUSIBLE LINK
|
Remove in this Direction | - | - |