While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Check if engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON and the engine starts.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| NG (for Manual Transaxle) | A |
| NG (for Automatic Transaxle) | B |
| OK (for Manual Transaxle) | C |
| OK (for Automatic Transaxle) | D |
A
B
C
D
Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).
OK
NG
Inspect the ignition switch assembly (See page Engine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION).
OK
NG
Disconnect the F13 ignition switch assembly connector.
Disconnect the A39 clutch start switch assembly connector.
Disconnect the B84 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F13-7 (ST2) - A39-2 | Always | Below 1 Ω |
| F13-7 (ST2) - B84-52 (NSW) | Always | Below 1 Ω |
| F13-7 (ST2) or A39-2 - Body ground | Always | 10 kΩ or higher |
| F13-7 (ST2) or B84-52 (NSW) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the ST relay from the engine room relay block.
Disconnect the A74 ECM connector.
Disconnect the A39 clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - A74-48 (STA) | Always | Below 1 Ω |
| 2 (ST relay) - A39-1 | Always | Below 1 Ω |
| A74-48 (STA), A39-1 or 2 (ST relay) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the park/neutral position switch (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
Inspect the ignition switch assembly (See page Engine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION).
OK
NG
Disconnect the F13 ignition switch assembly connector.
Disconnect the B88 park/neutral position switch connector.
Disconnect the B84 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F13-7 (ST2) - B88-4 (B) | Always | Below 1 Ω |
| F13-7 (ST2) - B84-52 (NSW) | Always | Below 1 Ω |
| F13-7 (ST2) or B88-4 (B) - Body ground | Always | 10 kΩ or higher |
| F13-7 (ST2) or B84-52 (NSW) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the ST relay from the engine room relay block.
Disconnect the A74 ECM connector.
Disconnect the B88 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - A74-48 (STA) | Always | Below 1 Ω |
| 2 (ST relay) - B88-5 (L) | Always | Below 1 Ω |
| A74-48 (STA) or B88-5 (L) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check that the battery is not depleted.
Battery is not depleted.
OK
NG
check that the battery terminals are not loose or corroded.
Battery terminals are not loose or corroded.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
OK
NG
Remove the ST relay from the engine room relay block.
Disconnect the A74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-48 (STA) - 2 (ST relay) | Always | Below 1 Ω |
OK
NG