Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below.


Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal is released
(c) STP signal is off when ST1- signal is off
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A257485E03
1.167,3.583 2.677,3.792 1.51,0.208 10 false No. 1 Integration Relay 0.76,1.177 2.323,1.385 1.563,0.208 10 false Ignition Switch Assembly 0.438,3.885 0.823,4.042 0.385,0.156 10 false MAIN 0.438,3.365 0.656,3.521 0.219,0.156 10 false R/I 0.208,1.313 0.51,1.458 0.302,0.146 10 false AM2 3.979,3.729 5.344,4.104 1.365,0.375 10 false Stop Light Switch Assembly 6.115,4.188 6.521,4.396 0.406,0.208 10 false ECM 5.615,0.927 6.01,1.073 0.396,0.146 10 false IGSW 5.615,2 5.958,2.146 0.344,0.146 10 false ST1- 5.615,3.073 5.927,3.24 0.313,0.167 10 false STP 5.26,3.219 5.583,3.396 0.323,0.177 10 false A74 5.26,2.125 5.594,2.292 0.333,0.167 10 false A74 5.26,1.052 5.583,1.24 0.323,0.188 10 false A74 5.302,3.021 5.521,3.208 0.219,0.188 10 false 36 5.302,1.938 5.521,2.104 0.219,0.167 10 false 35 5.302,0.854 5.542,1.021 0.24,0.167 10 false 28 4.906,1.979 5.021,2.135 0.115,0.156 10 false 3 4.906,3.083 5.021,3.24 0.115,0.156 10 false 1 4.063,1.99 4.167,2.146 0.104,0.156 10 false 4 4.042,3.083 4.156,3.229 0.115,0.146 10 false 2 2.99,2.948 3.208,3.094 0.219,0.146 10 false 1D 2.552,1.938 2.792,2.104 0.24,0.167 10 false 1D 2.99,2.292 3.208,2.438 0.219,0.146 10 false 1D 0.854,2.969 1.115,3.135 0.26,0.167 10 false 1C 0.854,2.479 1.094,2.635 0.24,0.156 10 false 1E 3.031,2.083 3.135,2.24 0.104,0.156 10 false 9 2.99,2.74 3.167,2.896 0.177,0.156 10 false 19 2.26,1.938 2.448,2.115 0.188,0.177 10 false 17 0.896,2.74 1.01,2.885 0.115,0.146 10 false 1 0.854,2.26 1.052,2.406 0.198,0.146 10 false 10 0.573,4.656 1.052,4.844 0.479,0.188 10 false Battery 1.354,4.375 1.729,4.563 0.375,0.188 10 false ALT 2.885,4.354 3.354,4.552 0.469,0.198 10 false STOP 1.01,0.542 1.396,0.729 0.385,0.188 10 false AM2 1.75,0.542 2.052,0.719 0.302,0.177 10 false IG2 3.979,3.552 4.25,3.698 0.271,0.146 10 false A38 2.135,3.083 2.469,3.271 0.333,0.188 10 false IG2 0.823,0.49 0.948,0.646 0.125,0.156 10 false 5 2.115,0.5 2.25,0.656 0.135,0.156 10 false 6 0.76,1.021 1.042,1.188 0.281,0.167 10 false F13 1.438,3.281 1.698,3.458 0.26,0.177 10 false IG2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the tester.

(a)

Connect the tester to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

(e)

Check the STP signal when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U158062E02
0.406,0.26 0.646,0.458 0.24,0.198 10 false *a 0.677,1.813 1.042,2.021 0.365,0.208 10 false A38

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U158063E02
0.406,0.26 0.646,0.458 0.24,0.198 10 false *a 0.667,1.823 1.052,2.073 0.385,0.25 10 false A38

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-4 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

4.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
U158102E01
0.374,0.311 0.571,0.508 0.198,0.198 10 *a 1.869,0.311 2.115,0.508 0.246,0.198 10 *b 0.374,2.322 0.585,2.533 0.211,0.211 10 *c 1.613,2.404 1.877,2.585 0.264,0.181 10 A74 1.786,3.654 1.583,4.255 false 1.872,3.654 2.113,4.267 false 2.004,4.284 2.412,4.443 0.408,0.159 10 STP 1.397,4.284 1.747,4.447 0.350,0.163 10 ST1-

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A74-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A74-36 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Text in Illustration
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the stop light switch connector.


b.

Remove the integration No. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A38-4 - 1D-19 Always Below 1 Ω
A38-4 or 1D-19 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR