The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil.
The crankshaft position sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and a magnet. The crankshaft position sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection duration and ignition timing are controlled.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0335 | Either of the following conditions (a) or (b) is met when camshaft position circuit fail is not detected (1 trip detection logic) :
(a) No crankshaft position sensor signal to ECM while cranking (b) No crankshaft position sensor signal to ECM while engine speed 600 rpm or more |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft position sensor plate ·
ECM |
| P0339 | Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more:
(1 trip detection logic) (a) Engine speed 1000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft position sensor plate ·
ECM |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
VV1+ is camshaft position sensor signals, and NE+ is the crankshaft position sensor signal.
A failure of the ground for the shielding of the wiring may result in noisy waveforms.
| ECM Terminal Name | CH1: Between VV1+ and NE-
CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Crankshaft position sensor |
| Required Sensors/Components (Related) | Camshaft position sensor |
| Frequency of Operation | Continuous |
| Crankshaft position sensor | ·
Crankshaft position sensor output voltage fluctuates while crankshaft revolving ·
34 crankshaft position sensor signal per crankshaft revolution |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Idle the engine for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All readiness.
Input the DTC: P0335 or P0339.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 and/or P0339 are output again, check the following items related to the camshaft position sensor.
Installation condition of the camshaft position sensor
Installation condition of the camshaft
Connection of the camshaft position sensor connector
If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
Check the engine speed. The engine speed can be checked using the intelligent tester. To check, follow the operation below:
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
The engine speed may be indicated as zero despite the engine rotating normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the tester.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.
OK
NG
Inspect the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B25-1 - B84-122 (NE+) | Always | Below 1 Ω |
| B25-2 - B84-121 (NE-) | Always | Below 1 Ω |
| B25-1 or B84-122 (NE+) - Body ground | Always | 10 kΩ or higher |
| B25-2 or B84-121 (NE-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the crankshaft position sensor installation.
Sensor is installed correctly.
| *a | OK |
| *b | NG |
| *c | Clearance |
OK
NG
Inspect the teeth of the crankshaft position sensor plate.
Crankshaft position sensor plate does not have any cracks or deformation.
OK
NG
Replace the crankshaft position sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine and run it at idle for 20 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0335 and/or P0339 are output | B |
If the engine does not start, replace the ECM.
A
B