Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.

The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. The signal from the heated oxygen sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric air-fuel ratio. This variance triggers a reduction in the fuel volume if the air-fuel ratio is rich, and an increase in the fuel volume if it is lean.

The short-term fuel trim varies from the central value due to individual engine differences, wear over time and changes in the operating environment. The long-term fuel trim, which controls overall fuel compensation, steadies long-term deviations of the short-term fuel trim from the central value.

If both the short-term fuel trim and the long-term fuel trim are lean or rich beyond a certain value, the ECM determines this to be a malfunction, illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0171 When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean side (2 trip detection logic)
·

Intake system

·

Injector blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leakage in exhaust system

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor (sensor 1) heater

·

No. 1 integration relay

·

PCV valve and hose

·

ECM

·

Wire harness


P0172 When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich side (2 trip detection logic)
·

Injector leak or blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leakage in exhaust system

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor (sensor 1) heater

·

No. 1 integration relay

·

ECM

·

Wire harness



HINT:
·

When DTC P0171 is recorded, the actual air-fuel ratio is on the lean side. When DTC P0172 is recorded, the actual air-fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be recorded. The MIL is then illuminated.

·

If the total of the short-term fuel trim value and long-term fuel trim value is within the malfunction threshold (and engine coolant temperature is more than 75°C (167°F)), the system is functioning normally.



MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection amounts that deviate from the ECM's estimated fuel amount will cause a change in the long-term fuel trim compensation value. Long-term fuel trim value is adjusted when persistent deviations in the short-term fuel trim's value are present. Also, the smoothed fuel trim learning value is adjusted when deviations from the ECM's simulated fuel injection value are present. The smoothed fuel trim learning value is a combination of smoothed short-term fuel trim (fuel feedback compensation value) and smoothed long-term fuel trim (learning value of the air-fuel ratio). When the smoothed fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

The smoothed fuel trim learning value is above 48% or below -35%. The ECM interprets this as a fault in the fuel system.

A381777E01
1.552,1.646 1.646,1.844 1.646,1.844 1.813,1.844 false 1.573,3.031 1.667,2.885 1.667,2.885 1.833,2.885 false 1.76,0.302 3.01,0.688 1.25,0.385 10 false Fuel Compensation Amount 1.917,1.74 2.271,1.948 0.354,0.208 10 false 1.48 1.927,2.281 2.281,2.49 0.354,0.208 10 false 1.0 1.938,2.802 2.292,3.01 0.354,0.208 10 false 0.65 0.292,1.281 1.51,1.802 1.219,0.521 10 false +48%: Malfunction Threshold of LEAN Condition 0.313,2.844 1.531,3.365 1.219,0.521 10 false -35%: Malfunction Threshold of RICH Condition

MONITOR STRATEGY

Required Sensors/Components Heated oxygen sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Fuel system status Closed loop
Battery voltage 11 V or higher
Either of following conditions 1 or 2 met -
1. Engine RPM Less than 1000 rpm
2. Intake air amount per revolution 0.09 g/rev or more

TYPICAL MALFUNCTION THRESHOLDS

Purge-cut Executing
Either of following conditions 1 or 2 met -
1. Average of short-term fuel trim and long-term fuel trim 48% or more (varies with engine coolant temperature)
2. Average of short-term fuel trim and long-term fuel trim -35% or more (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

A199233E93
0.568,0.043 1.536,0.247 0.968,0.205 10 Vehicle Speed 1.247,1.962 1.653,2.139 0.406,0.177 10 Idling 0.442,2.249 1.709,2.405 1.268,0.156 10 Ignition Switch ON 2.009,2.339 2.210,2.540 0.201,0.201 10 [A] 2.529,1.836 2.734,2.013 0.205,0.177 10 [B] 3.324,1.839 3.548,2.011 0.224,0.171 10 [C] 4.797,0.442 5.026,0.615 0.229,0.173 10 [D] 5.622,3.29 5.846,3.461 0.224,0.171 10 [E] 0.414,0.317 1.625,0.480 1.211,0.163 10 120 km/h (74 mph) 0.44,1.198 1.652,1.361 1.211,0.163 10 60 km/h (37 mph) 4.343,2.922 5.541,3.099 1.198,0.177 10 5 minutes or more 2.13,2.992 2.925,3.169 0.795,0.177 10 Warming up 2.858,3.146 4.014,3.323 1.156,0.177 10 2 minutes or more 3.636,0.059 7.009,0.262 3.373,0.202 10 Engine coolant temperature is 75°C (167°F) or higher 3.062,2.043 3.463,0.148 3.463,0.148 3.585,0.148 false

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn tester on [A].

6.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at between 60 and 120 km/h (37 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low heated oxygen sensor (sensor 1) voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high heated oxygen sensor (sensor 1) voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC P0171 or P0172 and other DTCs are output B



A

2.CHECK CONNECTION OF PCV HOSE

B

2.CHECK CONNECTION OF PCV HOSE
a.

OK:

PCV hose is connected correctly and is not damaged.



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.


f.

Perform the Control the Injection Volume with the engine idling.


g.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.

HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Tester Display (Sensor) Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
-12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V

Status of O2S B1S1 Status of O2S B1S2 Air-Fuel Ratio Condition and
Heated Oxygen Sensor Condition
Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - -
Lean Lean Actual air-fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector blockage

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Rich Rich Actual air-fuel ratio rich
·

Fuel injector leak or blockage

·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


Lean Lean/Rich Heated oxygen sensor (sensor 1) malfunction
·

Heated oxygen sensor (sensor 1) malfunction


B
Rich Lean/Rich Heated oxygen sensor (sensor 1) malfunction
·

Heated oxygen sensor (sensor 1) malfunction




HINT:

Lean: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) almost always indicates 0.4 V or less.

Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) almost always indicates 0.5 V or more.

Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) alternates correctly.



A

5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)

B

11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


d.

Read the Coolant Temp value when the engine is cold and warmed up.

Standard:
Tester Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 80 and 100°C (176 and 212°F)




OK

6.READ VALUE USING INTELLIGENT TESTER (MAF)

NG

6.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine speed.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
Tester Display Condition Specified Condition
MAF Shift lever position: N
A/C: OFF
Engine speed: 3000 rpm
Between 4.0 gm/sec and 8.0 gm/sec




OK

7.CHECK FUEL PRESSURE

NG

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
7.CHECK FUEL PRESSURE

OK

8.CHECK EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks.



OK

9.CHECK FOR SPARK AND IGNITION

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARK AND IGNITION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.




NEXT

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.


HINT:
·

Refer to the fuel injector inspection procedure (See page Engine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSPECTION).

·

If the injectors are malfunctioning, engine misfire may occur. The misfire counter can be read with the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.




OK

15.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.


OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
U158039E02
1.844,1.021 2.24,0.771 false 0.104,0.083 0.354,0.333 0.25,0.25 10 false *a 0.5,0.958 0.823,1.167 0.323,0.208 10 false B37 2.313,0.625 2.594,0.823 0.281,0.198 10 false +B

a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B37-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))



OK

13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

22.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (HT1A) - B84-109 (HT1A) Always Below 1 Ω
B37-3 (OX1A) - B84-112 (OX1A) Always Below 1 Ω
B37-4 (E2) - B84-90 (EX1A) Always Below 1 Ω
B37-1 (HT1A) or B84-109 (HT1A) - Body ground Always 10 kΩ or higher
B37-3 (OX1A) or B84-112 (OX1A) - Body ground Always 10 kΩ or higher
B37-4 (E2) or B84-90 (EX1A) - Body ground Always 10 kΩ or higher




OK

14.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)
a.

Replace the heated oxygen sensor (sensor 1) (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>REMOVAL).



NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS
16.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

19.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

END

19.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B72-3 (VG) - B84-118 (VG) Always Below 1 Ω
B72-2 (E2G) - B84-116 (E2G) Always Below 1 Ω
B72-3 (VG) or B84-118 (VG) - Body ground Always 10 kΩ or higher
B72-2 (E2G) or B84-116 (E2G) - Body ground Always 10 kΩ or higher




OK

20.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE MASS AIR FLOW METER
a.

Replace mass air flow meter (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.




NEXT

21.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
21.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0171 or P0172 is output B



A

END

B

22.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B37-2 (+B) - 1E-4 Always Below 1 Ω
B37-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR