Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL INJECTOR
RM19S0E _51 Engine / Hybrid System _051453 1NZ-FE FUEL _0248097 FUEL INJECTOR A

1NZ-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 12261 4.REMOVE VENTILATION HOSE

A115487

a.

Disconnect the ventilation hose.


Hide 23820 5.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

A115488

a.

Disconnect the fuel vapor feed hose assembly.


Hide 11201 6.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A115489

Disconnect the fuel injector connectors.


b.

for LHD:

i.
A260540

Disconnect the connector and 4 wire harness clamps shown in the illustration and disconnect the engine wire harness.


ii.
A115491

Remove the bolt and the wire harness bracket.



c.

for RHD:

i.
A260541

Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.



d.
A066472

Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.


Hide 23901 7.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A115492

Remove the EFI fuel pipe clamp.


b.
A260531E01
2.094,2.92 2.251,3.069 0.157,0.149 10 *1 2.649,3.962 2.806,4.111 0.157,0.149 10 *2 1.851,4.011 2.008,4.160 0.157,0.149 10 *3 2.353,3.344 2.215,3.096 false 2.652,3.709 2.728,3.95 false 1.092,4.009 1.249,4.158 0.157,0.149 10 *4 1.29,3.763 1.218,4.005 false 1.884,3.755 1.958,3.985 1.958,3.985 2.042,3.755 false

Pinch the retainer of the fuel tube connector, then pull the fuel tube connector to disconnect the fuel tube out of the fuel delivery pipe sub-assembly.

Text in Illustration
*1 Retainer
*2 Fuel Pipe
*3 O-Ring
*4 Nylon Tube
V100135

Pinch
V100136

Pull

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-ring that seals the pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a vinyl bag after disconnecting the fuel tube.

·

If the fuel tube connector and pipe are stuck, push and pull to release them.




Hide 23807 8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A115494

Remove the 3 bolts and the fuel delivery pipe sub-assembly with 4 fuel injectors.

NOTICE:

Do not drop the fuel injectors when removing the fuel delivery pipe sub-assembly.



Hide 23807V 9.REMOVE NO. 1 DELIVERY PIPE SPACER

A115496

a.

Remove the 2 No. 1 delivery pipe spacers.


Hide 23291 10.REMOVE INJECTOR VIBRATION INSULATOR

A152561

a.

Remove the 4 injector vibration insulators.


Hide 23250 11.REMOVE FUEL INJECTOR ASSEMBLY

a.
A115498

Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

Text in Illustration
V100135

Pull