Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.07–2016.09
RM19S0E _51 Engine / Hybrid System _051464 CRUISE CONTROL _0248153 CRUISE CONTROL SYSTEM T

CRUISE CONTROL  CRUISE CONTROL SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Cruise Control System
Symptom Suspected Area See page
Cruise control main switch cannot be turned on (Cruise control indicator in combination meter does not illuminate) Cruise control switch circuit (Click here)
Cruise main indicator light circuit (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
SET does not operate or CANCEL operates when it should not (DTC is not output) Cruise control switch circuit (Click here)
Clutch switch circuit*2 (Click here)
Automatic transaxle system (U340E)*1 (Click here)
Automatic transaxle system (U441E)*1 (Click here)
Anti-lock brake system*3 (Click here)
Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4 (Click here)
Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4 (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Actual vehicle speed deviates above or below set speed Anti-lock brake system*3 (Click here)
Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4 (Click here)
Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4 (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Cruise control is not canceled when brake pedal is depressed Stop light switch circuit (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Moving shift lever does not cancel cruise control*1 Automatic transaxle system (U340E)*1 (Click here)
Automatic transaxle system (U441E)*1 (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Cruise control is not canceled when clutch pedal is depressed*2 Clutch switch circuit*2 (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Control switch does not operate (-SET, +RES, CANCEL not possible) Cruise control switch circuit (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
SET is possible at less than approximately 40 km/h (25 mph), or CANCEL does not operate Anti-lock brake system*3 (Click here)
Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4 (Click here)
Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4 (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Poor response in ACCEL and RESUME modes Cruise control switch circuit (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
DTC memory is cleared ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
DTC is not output or is output when it should not be TC and CG terminal circuit (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Cruise control indicator light does not illuminate Cruise control switch circuit (Click here)
Cruise main indicator circuit (Click here)
Combination meter assembly (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)
Cruise control SET indicator does not illuminate (SET function operates normally) Cruise SET indicator light circuit (Click here)
Combination meter assembly (Click here)
ECM (for 2NZ-FE) (Click here)
ECM (for 1NZ-FE) (Click here)

*1: for Automatic Transaxle

*2: for Manual Transaxle

*3: w/ ABS

*4: w/ VSC