Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2011.08–2014.07
RM19S0E _53 Suspension _051472 FRONT SUSPENSION _0248215 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side as for the LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48619A 1.INSTALL STRUT MOUNTING BEARING

a.
C235444

Using a brass bar and press, install the strut mounting bearing onto the front coil spring upper seat.

NOTICE:

The strut mounting bearing must be securely installed.



Hide 48132 2.INSTALL FRONT COIL SPRING

a.
C107509E08
0.375,1.531 0.563,1.781 false 2.927,1.677 2.833,1.24 false 0.115,1.406 0.417,1.583 0.302,0.177 10 false SST 2.875,1.688 3.073,1.854 0.198,0.167 10 false *a

Using SST, compress the front coil spring.

Text in Illustration
*a Lower End

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)

NOTICE:

Do not use an impact wrench. It will damage SST.



b.

Install the front coil spring onto the front shock absorber.

NOTICE:

A spring of a smaller diameter should be installed in the upward direction.


HINT:

Fit the lower end of the front coil spring into the gap of the absorber lower seat.



Hide 48157C 3.INSTALL FRONT COIL SPRING UPPER INSULATOR

Hide 48331C 4.INSTALL FRONT SPRING BUMPER

a.
C107510E10
2.76,0.698 2.563,1.063 false 1,1.49 1.198,1.01 false 0.917,1.521 1.073,1.677 0.156,0.156 10 false *a 2.792,0.573 2.948,0.729 0.156,0.156 10 false *b

Install the front spring bumper onto the front coil spring upper seat with the air discharge groove of the front spring bumper and the rib portion of the front coil spring upper seat aligned.

Text in Illustration
*a Rib Portion
*b Air Discharge Groove

NOTICE:

Securely insert the spring bumper into the coil spring upper seat.



Hide 48471C 5.INSTALL FRONT COIL SPRING UPPER SEAT

a.

Install the front coil spring upper seat with the strut mounting bearing and front spring bumper onto the front shock absorber.


b.

Provisionally tighten a new nut.


c.

Remove SST from the front coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.



d.
C229624E09
1.208,0.771 0.948,0.323 false 1.51,0.698 1.969,0.906 false 2.01,0.854 2.177,1.052 0.167,0.198 10 false *1 0.719,0.156 1.031,0.323 0.313,0.167 10 false SST

Using SST and socket hexagon wrench 6, fix the shock absorber rod and tighten the nut.

Text in Illustration
*1 Long Socket Hexagon Wrench 6

SST
09729-97202  

Torque:
without SST : 33 N*m (340 kgf*cm, 25 ft.*lbf)
with SST : 27 N*m (278 kgf*cm, 20 ft.*lbf)

HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and a SST with a fulcrum length of 40 mm (1.57 in.).

·

If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 48609 6.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

Hide 48520 7.TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C235028

Provisionally tighten a new nut through the front No. 2 suspension support.


b.

Install the front shock absorber with coil spring onto the steering knuckle.


c.

Install the 2 bolts and 2 nuts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

HINT:

Keep the bolt from rotating while installing and tightening the nuts.



Hide 47313A 8.INSTALL FRONT FLEXIBLE HOSE (w/ ABS)

a.

Install the front flexible hose and front speed sensor with the bolt.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose and front speed sensor without twisting them.



Hide 47313A 9.INSTALL FRONT FLEXIBLE HOSE (w/o ABS)

a.

Install the front flexible hose with the bolt.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose without twisting them.



Hide 48810 10.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

Using a socket hexagon wrench 6 to hold the stud.



Hide 11.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48520 12.FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C234273E06
1.781,1.521 1.781,1.219 true 1.656,1.542 2.021,1.771 0.365,0.229 10 true SST 1.188,0.406 1.354,0.573 0.167,0.167 10 false *a 3.208,0.906 3.375,1.073 0.167,0.167 10 false *b

Using SST and socket hexagon wrench 6, fix the front shock absorber rod and tighten the nut.

Text in Illustration
*a Hold
*b Turn

SST
09729-97202  

Torque:
with SST : 55 N*m (561 kgf*cm, 41 ft.*lbf)
without SST : 48 N*m (485 kgf*cm, 35 ft.*lbf)


Hide 48684B 13.INSTALL FRONT SUSPENSION SUPPORT DUST COVER

Hide 55722C 15.INSTALL INNER COWL TOP TO COWL BRACE

Hide 55815E 16.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 55735D 17.INSTALL FRONT AIR SHUTTER SEAL RH

Hide 85110 18.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 19.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT