Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2014.07
RM19S0E _53 Suspension _051472 FRONT SUSPENSION _0248215 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side as for the LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 85110 1.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55815E 2.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55735D 3.REMOVE FRONT AIR SHUTTER SEAL RH

Hide 55722C 4.REMOVE INNER COWL TOP TO COWL BRACE

Hide 55711 5.REMOVE OUTER COWL TOP PANEL

Hide 6.REMOVE FRONT WHEEL

Hide 48810 7.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C235026

Remove the nut and separate the front stabilizer link assembly from the shock absorber.

HINT:

Using a socket hexagon wrench 6 to hold the stud.



Hide 47313A 8.SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)

a.
C107502

Remove the bolt to separate the front speed sensor and front flexible hose.


Hide 47313A 9.SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)

a.

Remove the bolt and separate the front flexible hose.


Hide 48684B 10.REMOVE FRONT SUSPENSION SUPPORT DUST COVER

Hide 48520 11.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C107503

Remove the 2 nuts and 2 bolts to separate the front shock absorber with coil spring from the steering knuckle.

HINT:

Keep the bolt from rotating while loosening and removing the nuts.



b.
C235027

Using a 6 mm hexagon socket wrench, fix the front shock absorber rod and remove the nut.


c.

Remove the front No. 2 suspension support.


d.

Remove the front shock absorber with coil spring from the vehicle.


Hide 48609 12.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

Hide 48304B 13.REMOVE BUMPER SEAT SUB-ASSEMBLY

a.
C107505

Using a 6 mm hexagon socket wrench, fix the shock absorber rod and loosen the nut.


b.
C107506E03
2.652,1.128 2.955,1.287 0.304,0.159 10 SST 2.619,1.211 2.387,1.236 false

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)

NOTICE:

Do not use an impact wrench. It will damage SST.



c.
C275706E03
0.303,0.093 0.473,0.253 0.170,0.161 10 *a 0.303,2.563 0.473,2.723 0.170,0.160 10 *b 2.101,1.14 2.417,1.303 0.317,0.163 10 SST 1.823,1.23 2.067,1.23 false 2.098,3.593 2.414,3.756 0.317,0.163 10 SST 1.82,3.683 2.064,3.683 false

Attach the arm of SST to the diameter of the front coil spring.

*a Correct
*b Incorrect

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




d.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench. It will damage SST.




e.

Confirm that the front coil spring becomes free and remove the nut.

CAUTION:

Do not remove the nut when the front coil spring is not free.



f.

Shock Absorber Type A:

i.

Remove the bumper seat sub-assembly with the front coil spring upper insulator from the front shock absorber.



g.

Shock Absorber Type B:

i.
C359303C02
0.802,1.781 1.333,1.646 false 1.385,1.594 1.615,1.823 1.615,1.823 1.813,1.594 true 0.615,1.719 0.927,1.917 0.313,0.198 10 false *1 1.583,1.833 1.896,2.031 0.313,0.198 10 false *a
*1 Front Spring Bumper Sub-assembly
*a Claw


Disengage the front coil spring upper insulator from the claws of the front shock absorber.


ii.

Remove the bumper seat sub-assembly with the front coil spring upper insulator from the front shock absorber.



Hide 48157C 14.REMOVE FRONT COIL SPRING UPPER INSULATOR

a.

Remove the front coil spring upper insulator from the bumper seat sub-assembly.


Hide 48132 15.REMOVE FRONT COIL SPRING

Hide 48158C 16.REMOVE FRONT COIL SPRING LOWER INSULATOR

a.

Remove the front coil spring lower insulator from the front shock absorber.