Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (airbag sensor assembly) via the CAN communication system.

The yaw rate and deceleration sensor (airbag sensor assembly) has a built-in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the yaw rate and deceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is set.

These DTCs are also output when calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1436 Either of the following is detected:
1.

With the vehicle stationary, the yaw rate and deceleration sensor output value is not 0 deg/s.

2.

Abnormal comparison value.


Yaw rate and deceleration sensor (Airbag sensor assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When U0124 and/or U0126 is output together with C1436, inspect and repair the trouble areas indicated by U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>U0073).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (YAW RATE SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor/min.: -128°/s, max.: 127°/s 0°/s: Vehicle stopped
-128 to 0°/s: Turning right
0 to 127°/s: Turning left
-


f.

Check that the yaw rate and deceleration sensor (airbag sensor assembly) output value displayed on the intelligent tester.

Result
Result Proceed to
NG (The yaw rate and deceleration sensor (airbag sensor assembly) output value is 0 deg/s when the vehicle is stationary, but the value fluctuates when turning) A
NG (The yaw rate and deceleration sensor (airbag sensor assembly) output value is not 0 deg/s when the vehicle is stationary) B
OK C

NOTICE:

Check the yaw rate and deceleration sensor (airbag sensor assembly) signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).




A

2.CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) INSTALLATION

B

REPLACE YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

C

2.CHECK YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and deceleration sensor (airbag sensor assembly) has been installed properly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor should not be installed in a tilted position.


NOTICE:

Check the yaw rate and deceleration sensor (airbag sensor assembly) signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).




OK

REPLACE YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

NG

INSTALL YAW RATE AND DECELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) CORRECTLY