Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › from 2014.07
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. DTC Detection Condition Trouble Area
C1426 After a stuck judgement* has been made within 10 minutes of stopping the vehicle, then after driving at a speed of 35 km/h or more and then slowing to 3 km/h or less, the stuck judgement* continues.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



*: While the master pressure sensor output value (voltage) is 0.86 V or more, there is no stop switch signal for 5 seconds or more continuously.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-

OK:

The tester displays ON or OFF according to brake pedal operation.




OK

3.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER SENSOR)

NG

5.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading/Min.: 0 V, Max.: 5 V 0.3 to 0.9 V: When brake pedal is released Reading increases when brake pedal is depressed.

OK:

Data Monitor voltage is within the specified range.




OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTC C1381 is not output A
DTC C1381 is output B


OK

NG

5.CHECK BRAKE PEDAL HEIGHT AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation. (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION ).

OK:

The brake pedal height and stop light switch assembly installation are normal.




OK

6.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

ADJUST BRAKE PEDAL HEIGHT OR STOP LIGHT SWITCH ASSEMBLY INSTALLATION

6.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.
U158458E01
0.044,0.021 0.243,0.183 0.199,0.162 10 *a 1.589,0.159 1.872,0.307 0.284,0.149 10 A54 0.066,1.022 0.357,1.170 0.291,0.149 10 STP 1.244,0.912 0.438,1.097 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-2 (STP) - Body ground Stop light switch ON
(Brake pedal depressed)
8 to 14 V
Stop light switch OFF
(Brake pedal released)
Below 1.5 V



Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU (Brake Actuator Assembly))


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR