Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › 2011.08–2014.07
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248229 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSTALLATION  


PROCEDURE

Hide 44546A 1.INSTALL BRAKE ACTUATOR BOLT CUSHION

a.

Install the 3 brake actuator bolt cushions to the brake actuator bracket assembly.


b.

Install the 3 brake actuator case collars to the brake actuator bolt cushion.


Hide 44590 2.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY

a.
C228795E02
0.823,0.656 0.979,0.813 0.156,0.156 10 false 1 1.302,0.458 1.479,0.646 0.177,0.188 10 true 2 1.313,1.531 1.469,1.729 0.156,0.198 10 true 3

Install the actuator bracket with the 3 bolts in the sequence shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plug before connecting the brake tube. New actuators are filled with brake fluid.

·

Do not carry an actuator by its connector.




Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY (w/o VSC)

a.
C169912E03
1.073,1.688 1.208,1.885 0.135,0.198 10 true 1 2.656,1.635 2.771,1.813 0.115,0.177 10 false 2 2.729,0.958 2.896,1.135 0.167,0.177 10 true 3

Install the brake actuator with bracket with the 3 bolts in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not damage the brake tubes or wire harness.



b.
C420067C01
1.604,0.698 2.135,0.302 2.135,0.302 2.24,0.302 true 0.729,0.24 0.802,0.24 0.802,0.24 1.24,0.604 true 0.25,1.083 0.354,1.083 0.354,1.083 1.448,0.958 true 0.354,0.667 0.458,0.667 0.458,0.667 1.042,0.792 true 1.74,0.781 2.198,0.552 2.198,0.552 2.302,0.552 true 1.438,0.646 1.813,0.188 1.813,0.188 1.917,0.188 true 0.188,0.594 0.375,0.771 0.188,0.177 10 true *a 0.063,1 0.26,1.198 0.198,0.198 10 true *b 2.344,0.469 2.563,0.667 0.219,0.198 10 true *c 2.281,0.219 2.479,0.417 0.198,0.198 10 true *d 1.958,0.115 2.135,0.281 0.177,0.167 10 true *e 0.542,0.177 0.74,0.375 0.198,0.198 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten each brake tube to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




c.

Using a union nut wrench 10 mm, connect the 6 brake tubes to the brake actuator assembly.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.
C228100E02
1.484,1.288 1.692,1.515 0.208,0.227 10 *1 1.218,1.308 1.462,1.377 false

Connect the brake actuator connector.

Text in Illustration
*1 Lock Lever

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.




Hide 44510 4.INSTALL BRAKE ACTUATOR ASSEMBLY (w/ VSC)

a.
C228794E02
0.823,1.875 0.958,2.052 0.135,0.177 10 true 1 1.271,1.948 1.406,2.115 0.135,0.167 10 true 2 2.542,1.021 2.646,1.177 0.104,0.156 10 false 3

Install the brake actuator with bracket with the 3 bolts in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not damage the brake tubes or wire harness.



b.
C420068C01
1.594,0.594 2.135,0.302 2.135,0.302 2.24,0.302 true 0.729,0.24 0.802,0.24 0.802,0.24 1.156,0.49 true 0.229,0.969 0.333,0.969 0.333,0.969 1.469,0.896 true 0.354,0.667 0.458,0.667 0.458,0.667 0.99,0.76 true 1.76,0.635 2.198,0.552 2.198,0.552 2.302,0.552 true 1.417,0.542 1.813,0.188 1.813,0.188 1.917,0.188 true 0.188,0.594 0.375,0.771 0.188,0.177 10 true *a 0.063,0.896 0.26,1.094 0.198,0.198 10 true *b 2.344,0.469 2.563,0.667 0.219,0.198 10 true *c 2.281,0.219 2.479,0.417 0.198,0.198 10 true *d 1.958,0.115 2.135,0.281 0.177,0.167 10 true *e 0.542,0.177 0.74,0.375 0.198,0.198 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten each brake tube to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.




c.

Using a union nut wrench 10 mm and union nut wrench 12 mm, connect the 6 brake tubes to the brake actuator assembly.

Torque:
Flare Nut 10 mm : 15 N*m (155 kgf*cm, 11 ft.*lbf)
Flare Nut 12 mm : 20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.
C228100E02
1.484,1.288 1.692,1.515 0.208,0.227 10 *1 1.218,1.308 1.462,1.377 false

Connect the brake actuator connector.

Text in Illustration
*1 Lock Lever

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.




Hide 74431 6.INSTALL BATTERY TRAY

Hide 8.BLEED BRAKE LINE

Hide 9.BLEED CLUTCH LINE (for Manual Transmission)