Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

The Slip indicator light blinks during VSC, TRC operation.

If any of the following is detected, the Slip indicator light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the brake actuator (skid control ECU).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The VSC, TRC control system is defective.

HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU (brake actuator assembly) is abnormal.



WIRING DIAGRAM

C240011E01
5.31,1.996 7.038,2.300 1.728,0.304 10 Skid Control ECU (Brake Actuator Assembly) 1.471,0.475 2.025,0.617 0.553,0.141 10 CAN I/F 0.562,0.605 0.910,0.742 0.347,0.137 10 CPU 0.807,1.66 1.120,1.844 0.312,0.184 10 Slip 1.518,2.235 1.706,2.400 0.188,0.165 10 IG 0.665,3.207 2.360,3.364 1.695,0.157 10 : CAN Communication Line 0.307,2.548 2.181,2.720 1.874,0.172 10 Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

6.READ VALUE USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)

NG

6.READ VALUE USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Slip Indicator Light SLIP indicator light/OFF or ON OFF: Indicator light off
ON: Indicator light on
-


g.

When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Slip Indicator Light Slip indicator light Indicator light OFF/ON Observe combination meter
[Vehicle condition]
Vehicle stopped

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF B
OFF Changes between ON and OFF A
Does not change between ON and OFF B


A

7.REPLACE COMBINATION METER ASSEMBLY

B

8.CHECK COMBINATION METER ASSEMBLY
a.

Perform Active Test of the combination meter assembly using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The Slip indicator light turns on or off in accordance with the intelligent tester.




OK

END

NG