Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  VSC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC OFF indicator light will come on.

If VSC and traction control turns OFF, the TRC OFF indicator and VSC OFF indicator light will come on.

The VSC OFF indicator light is illuminated when the VSC and TRC controls are prohibited by operating the VSC OFF switch.

By pressing the VSC OFF switch for 3 seconds or longer, the VSC OFF mode is activated, the VSC and TRC controls are prohibited, and both the VSC OFF indicator light and the TRC OFF indicator light in the combination meter are illuminated.

WIRING DIAGRAM

C243296E02
0.595,0.585 0.916,0.739 0.320,0.153 10 CPU 1.536,0.444 2.056,0.593 0.520,0.150 10 CAN I/F 0.81,1.627 1.467,1.775 0.658,0.148 10 VSC OFF 1.536,2.218 1.729,2.370 0.193,0.152 10 IG 0.37,2.513 2.210,2.670 1.841,0.157 10 Combination Meter Assembly 2.963,1.775 3.234,1.928 0.271,0.153 10 F57 2.97,1.92 4.060,2.070 1.090,0.150 10 VSC OFF Switch 3.024,1.362 3.120,1.515 0.097,0.153 10 3 3.987,1.362 4.084,1.515 0.097,0.153 10 6 3.184,1.553 3.311,1.702 0.127,0.150 10 E 3.815,1.553 3.942,1.702 0.127,0.150 10 + 5.15,1.346 5.338,1.507 0.188,0.161 10 30 5.418,1.453 5.780,1.607 0.362,0.153 10 CSW 5.183,2.007 5.456,2.151 0.273,0.144 10 A54 5.183,2.167 6.891,2.514 1.708,0.347 10 Skid Control ECU (Brake Actuator Assembly) 0.649,3.205 2.374,3.364 1.725,0.159 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

OK

5.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)

NG

8.INSPECT VSC OFF SWITCH
7.CHECK COMBINATION METER ASSEMBLY
a.

Connect the intelligent tester to the DLC3.


b.

Perform Active Test of the combination meter assembly using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The VSC OFF indicator light turns on or off in accordance with the intelligent tester.




OK

END

NG