Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (yaw rate sensor) via the CAN communication system.

The yaw rate and deceleration sensor (yaw rate sensor) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (yaw rate sensor) and the CAN communication system, the DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are output.

The DTCs are also output when the calibration has not been completed.

DTC No. DTC Detection Condition Trouble Area
C1210 Zero point calibration of yaw rate sensor undone.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Skid control ECU (Brake actuator assembly)


C1336 Zero point calibration of acceleration sensor undone.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).


HINT:

When DTC U0123, U0124 and/or U0126 is output together with DTC C1210 and/or C1336, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>U0073).


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and deceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



Result
Result Proceed to
NG A
OK B


A

3.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR)

B

END

3.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR)
a.

Turn the ignition switch off.


b.

Check that the yaw rate and deceleration sensor (yaw rate sensor) has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor is not installed in a tilted position.




OK

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND DECELERATION SENSOR)

NG

INSTALL YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) CORRECTLY

4.READ VALUE USING INTELLIGENT TESTER (YAW RATE AND DECELERATION SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the intelligent tester, read the Data List.

ABS/VSC/TRC (Skid Control ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor/
min.: -18.525 m/s2,
max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2/
min.: -18.525 m/s2,
max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Yaw Rate Sensor Yaw rate sensor/
min.: -128°/s,
max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-


f.

Check the yaw rate and deceleration sensor (yaw rate sensor) output value displayed on the intelligent tester.

OK:

The yaw rate and deceleration sensor (yaw rate sensor) output value is normal.


NOTICE:

Check the yaw rate and deceleration sensor (yaw rate sensor) signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).



HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



OK

NG

REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR)