Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1277  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1415  Rear Speed Sensor RH Output Malfunction  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1403 and C1404 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1273).

DTC No. DTC Detection Condition Trouble Area
C1415
C1416
Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)



Test Mode Diagnosis Code
DTC No. DTC Detection Condition Trouble Area
C1277
C1278
Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Speed sensor rotor



HINT:
·

DTC C1415 and C1277 are for the rear speed sensor RH.

·

DTC C1416 and C1278 are for the rear speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

6.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.




OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1415 and C1416 are not output A
DTCs C1415 and/or C1416 are output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR)
5.CHECK REAR SPEED SENSOR INSTALLATION

OK

6.INSPECT SKID CONTROL SENSOR WIRE

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR)

6.INSPECT SKID CONTROL SENSOR WIRE

OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

REPLACE SKID CONTROL SENSOR WIRE

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

OK

8.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1415 and/or C1416 are output A
DTCs C1415 and C1416 are not output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR)

B

10.REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (REAR SPEED SENSOR, SENSOR ROTOR)
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor and rear axle hub and bearing assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1415 and C1416 are not output A
DTCs C1415 and/or C1416 are output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

END

B