Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C146E  Open in ABS Solenoid Relay Circuit  C146F  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid and TRC solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self diagnosis performed when the engine starts running.

The ABS solenoid relay is housed in the skid control ECU in the actuator assembly.

DTC No. DTC Detection Condition Trouble Area
C146E When either of the following is detected:
1.

Both of the following conditions continue for 0.22 seconds or more.

-

The IG1 terminal voltage is 9.5 V or more.

-

The solenoid relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.22 seconds or more.

-

The IG1 terminal voltage becomes lower than 9.5 V or less when the relay is turned on.

-

The relay contact remains open.



·

ABS NO. 2 fuse

·

ABS solenoid relay circuit

·

Brake actuator assembly (ABS solenoid relay)


C146F Immediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4 seconds when the relay is turned off.
·

ABS solenoid relay circuit

·

Brake actuator assembly (ABS solenoid relay)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1241).


PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Check the connector case and terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.
U158456E01
0.044,0.021 0.243,0.183 0.199,0.162 10 *a 1.589,0.159 1.872,0.307 0.284,0.149 10 A54 2.984,0.83 3.275,0.978 0.291,0.149 10 +BS 2.465,0.956 2.957,0.922 false

Disconnect the brake actuator assembly (skid control ECU) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-12 (+BS) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)