Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL › 2011.08–2014.07
RM19S0E _54 Brake _051476 BRAKE SYSTEM (OTHER) _0248240 BRAKE PEDAL A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  INSTALLATION  


PROCEDURE

Hide 55106 1.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

a.

Temporarily install the pedal support with the bolt and 4 nuts.


b.
C241860E03
0.208,0.344 0.344,0.563 0.135,0.219 10 false 1 2.021,0.333 2.229,0.552 0.208,0.219 10 true 2 2.063,1.448 2.271,1.667 0.208,0.219 10 true 4 0.25,1.521 0.458,1.74 0.208,0.219 10 false 3

Tighten the 4 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Tighten the bolt.

Torque:
24 N*m (241 kgf*cm, 17 ft.*lbf)


Hide 55106 2.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

a.

Temporarily install the pedal support with the bolt and 4 nuts.


b.
C233125E01
0.739,0.64 0.837,0.790 0.098,0.151 10 1 0.815,1.3 0.913,1.450 0.098,0.151 10 3 2.13,1.231 2.228,1.382 0.098,0.151 10 4 2.077,0.568 2.174,0.718 0.098,0.151 10 2

Tighten the 4 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Tighten the bolt.

Torque:
24 N*m (241 kgf*cm, 17 ft.*lbf)


d.

Install the wire harness clamp.


Hide 45260 3.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

a.
U134712E01
2.002,3.8 2.116,3.967 0.114,0.167 10 A 2.747,2.779 2.862,2.946 0.114,0.167 10 B 2.121,1.416 2.240,1.583 0.118,0.167 10 C 1.994,1.975 2.180,2.161 0.186,0.186 10 *a 0.505,3.03 0.691,3.216 0.186,0.186 10 *b 2.177,2.074 2.73,2.284 false 2.177,2.074 2.841,2.216 false 2.788,2.255 2.689,2.305 false 2.884,2.207 2.808,2.245 false

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.

Text in Illustration
*a Matchmark
*b Front of the Vehicle


b.

Tighten the bolt B while aligning the No. 2 steering intermediate shaft assembly with the position C as shown in the illustration.

Standard C:

18.5 to 19.7 mm


Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


c.

Tighten bolt A.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 47264D 4.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Apply lithium soap base glycol grease to the push rod pin.


b.
C245309E01
0.114,0 0.528,0.338 0.414,0.338 10 *A 0.114,2.333 0.528,2.671 0.414,0.338 10 *B

Install the push rod clevis with the push rod pin and a new clip.

Text in Illustration
*A for LHD
*B for RHD
V100144

Apply Lithium Soap Base Glycol Grease


c.

Install the brake pedal return spring.


Hide 84340 5.INSTALL STOP LIGHT SWITCH ASSEMBLY

a.
F049043E33
0.594,1.177 0.458,1.521 false 1.792,1.333 2,1.531 false 1.198,0.479 1.406,0.177 false 1.438,0.063 1.615,0.26 0.177,0.198 10 false *1 1.938,1.531 2.115,1.729 0.177,0.198 10 false *2 0.365,1.521 0.531,1.719 0.167,0.198 10 false *3

Insert the stop light switch into the adjuster until it just touches the brake pedal.

Text in Illustration
*1 Adjuster
*2 Stop Light Switch Assembly
*3 Brake Pedal

NOTICE:

Do not depress the brake pedal.



b.
C172890E18
1.635,0.698 1.635,0.219 1.635,0.219 1.74,0.219 false 0.74,1.771 0.917,1.938 0.177,0.167 10 false *a 1.771,0.135 1.948,0.281 0.177,0.146 10 false *1

Make a quarter turn clockwise to install the stop light switch.

Text in Illustration
*1 Stop Light Switch Assembly
*a Stop Light Switch Clearance

NOTICE:

Do not depress the brake pedal.


HINT:

The turning torque for installing the stop light switch:


Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

or less



c.

Check the stop light switch clearance.

Stop light switch clearance:

0.5 to 2.6 mm (0.020 to 0.102 in.)



d.

Engage the harness clamp to the pedal support.


e.

Connect the connector to the stop light switch.


Hide 55432B 6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

Hide 73900 7.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55433B 8.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD)

Hide 55606 9.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 83100 10.INSTALL COMBINATION METER ASSEMBLY

Hide 11.INSPECT AND ADJUST BRAKE PEDAL