Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL › from 2014.07
RM19S0E _54 Brake _051476 BRAKE SYSTEM (OTHER) _0248240 BRAKE PEDAL A

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  INSTALLATION  


PROCEDURE

Hide 55106 1.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

a.

Temporarily install the pedal support with the bolt and 4 nuts.


b.
C233125E01
0.739,0.64 0.837,0.790 0.098,0.151 10 1 0.815,1.3 0.913,1.450 0.098,0.151 10 3 2.13,1.231 2.228,1.382 0.098,0.151 10 4 2.077,0.568 2.174,0.718 0.098,0.151 10 2

Tighten the 4 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Tighten the bolt.

Torque:
24 N*m (241 kgf*cm, 17 ft.*lbf)


d.

Install the wire harness clamp.


Hide 47264D 2.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Apply lithium soap base glycol grease to the push rod pin.


b.
C235059E02
0.476,1.884 0.684,2.047 0.208,0.163 10 *1

Install the push rod clevis with the push rod pin and a new clip.

Text in Illustration
*1 Apply Lithium Soap Base Glycol Grease


c.

Install the brake pedal return spring.


Hide 84340 3.INSTALL STOP LIGHT SWITCH ASSEMBLY

a.
F049043E33
0.594,1.177 0.458,1.521 false 1.792,1.333 2,1.531 false 1.198,0.479 1.406,0.177 false 1.438,0.063 1.615,0.26 0.177,0.198 10 false *1 1.938,1.531 2.115,1.729 0.177,0.198 10 false *2 0.365,1.521 0.531,1.719 0.167,0.198 10 false *3

Insert the stop light switch into the adjuster until it just touches the brake pedal.

Text in Illustration
*1 Adjuster
*2 Stop Light Switch Assembly
*3 Brake Pedal

NOTICE:

Do not depress the brake pedal.



b.
C172890E18
1.635,0.698 1.635,0.219 1.635,0.219 1.74,0.219 false 0.74,1.771 0.917,1.938 0.177,0.167 10 false *a 1.771,0.135 1.948,0.281 0.177,0.146 10 false *1

Make a quarter turn clockwise to install the stop light switch.

Text in Illustration
*1 Stop Light Switch Assembly
*a Stop Light Switch Clearance

NOTICE:

Do not depress the brake pedal.


HINT:

The turning torque for installing the stop light switch:


Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

or less



c.

Check the stop light switch clearance.

Stop light switch clearance:

0.5 to 2.6 mm (0.020 to 0.102 in.)



d.

Engage the harness clamp to the pedal support.


e.

Connect the connector to the stop light switch.


Hide 73900 4.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 83100 6.INSTALL COMBINATION METER ASSEMBLY

Hide 7.INSPECT AND ADJUST BRAKE PEDAL