Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511  Torque Sensor Circuit Malfunction  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

While DTC C1511 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1511 Torque Sensor1 Diagnosis Condition: IG ON
Malfunction Status: TRQ1 voltage is less than 0.25 V or more than 4.6 V
·

Torque sensor (Steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Ignition switch ON again

WIRING DIAGRAM

C375646E10
5.844,0.594 6.156,0.792 0.313,0.198 10 false 5V 5.094,0.802 5.708,1 0.615,0.198 10 false TRQV 5.135,1.594 5.75,1.792 0.615,0.198 10 false TRQ1 5.115,2.271 5.729,2.469 0.615,0.198 10 false TRQG 4.875,0.802 5.063,1.031 0.188,0.229 10 false 8 4.885,1.479 5.042,1.677 0.156,0.198 10 false 9 4.885,2.229 5.042,2.427 0.156,0.198 10 false 2 4.854,2.938 5.167,3.135 0.313,0.198 10 false z6 4.854,3.094 7.156,3.375 2.302,0.281 10 false Power Steering ECU Assembly 0.427,3.01 2.427,3.406 2,0.396 10 false Torque Sensor (Steering Column Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

If the steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



PROCEDURE

1.INSPECT POWER STEERING ECU ASSEMBLY (TORQUE SENSOR OUTPUT)
a.
C375640C08
0.365,0.969 0.76,1.229 0.396,0.26 1.781,0.896 2.24,0.406 true 1.958,1.479 2.344,1.833 true 1.677,1.49 1.271,1.885 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 0.875,1.833 1.49,2.031 0.615,0.198 10 false TRQV 2.427,1.792 3.042,1.99 0.615,0.198 10 false TRQ1 2.313,0.354 2.927,0.552 0.615,0.198 10 false TRQG 0.5,1.031 0.813,1.229 0.313,0.198 10 false z6
*a Component without harness connected
(Torque Sensor (Steering Column Sub-assembly))


Disconnect the power steering ECU assembly connector.


b.

Connect 3 new 1.5 V batteries in series to prepare a 4.5 V power supply.

HINT:

Check that the voltage of the prepared power supply is 4.5 V.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z6-1(TRQ1) - z6-2(TRQG)
1.

Connect the 4.5 V positive (+) terminal to z6-8 (TRQV) and 4.5 V negative (-) terminal to z6-2 (TRQG)

2.

Steering wheel not being turned (without load)


2.07 to 2.43 V
1.

Connect the 4.5 V positive (+) terminal to z6-8 (TRQV) and 4.5 V negative (-) terminal to z6-2 (TRQG)

2.

Steering wheel being turned to right with vehicle stopped


2.25 to 3.42 V
1.

Connect the 4.5 V positive (+) terminal to z6-8 (TRQV) and 4.5 V negative (-) terminal to z6-2 (TRQG)

2.

Steering wheel being turned to left with vehicle stopped


1.08 to 2.25 V


NOTICE:

To avoid damaging the torque sensor (steering column assembly), do not apply a voltage of more than 5 V.


HINT:
·

The voltage values specified above are applicable when using an applied voltage of 4.5 V, and vary depending on the applied voltage (When compared to values for an applied voltage of 5 V, these values differ by a factor of 0.9).

·

When using an applied voltage of 5 V, the specified values are as follows.

Condition Specified Condition
Steering wheel not being turned (without load) 2.3 to 2.7 V
Steering wheel being turned to right with vehicle stopped 2.5 to 3.8 V
Steering wheel being turned to left with vehicle stopped 1.2 to 2.5 V



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE STEERING COLUMN SUB-ASSEMBLY

D

REPLACE STEERING COLUMN SUB-ASSEMBLY