Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051484 NAVIGATION / MULTI INFO DISPLAY _0248277 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E291132E19
0.833,0.156 2.104,0.563 1.271,0.406 10 false Roof Antenna Pole Sub-assembly 5.781,2.458 7.083,2.906 1.302,0.448 10 false Navigation Receiver Assembly 4.406,2.26 5.417,2.615 1.01,0.354 10 false Antenna Cord Sub-assembly 2.031,2.292 3.344,2.646 1.313,0.354 10 false No. 2 Antenna Cord Sub-assembly 4.177,1.271 4.302,1.427 0.125,0.156 10 false 2 4.167,1.552 4.396,1.708 0.229,0.156 10 false 1 3.24,1.271 3.365,1.427 0.125,0.156 10 false 2 3.24,1.552 3.469,1.708 0.229,0.156 10 false 1 6.042,1.323 6.75,1.479 0.708,0.156 10 false MAIN 6.042,1.667 6.667,1.823 0.625,0.156 10 false ANT+ 5.469,1.26 5.573,1.417 0.104,0.156 10 false 3 5.469,1.542 5.698,1.698 0.229,0.156 10 false 5 2.083,1.25 2.188,1.406 0.104,0.156 10 false 2 2.083,1.552 2.313,1.708 0.229,0.156 10 false 3 5.781,2.302 6.063,2.458 0.281,0.156 10 false RA 0.698,2.063 1.865,2.625 1.167,0.563 10 false Amplifier Antenna Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK NAVIGATION RECEIVER ASSEMBLY
3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the ignition switch to ACC with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.




OK

4.INSPECT ROOF ANTENNA POLE SUB-ASSEMBLY

NG

4.INSPECT ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.



OK

5.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

5.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the RA navigation receiver assembly connector.


b.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on
11 to 14 V




OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E298846E05
0.519,0.231 0.748,0.444 0.230,0.213 10 *a 0.582,1.9 0.812,2.113 0.230,0.213 10 *b

Disconnect the antenna connector from the amplifier antenna assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2 Always Below 1 Ω
1 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
1 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)



OK

7.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U158746E02
1.698,1.208 1.104,1.427 true 2.729,0.76 2.146,0.969 true 0.917,0.875 1.125,1.052 0.208,0.177 10 false RA 0.104,0.042 0.333,0.24 0.229,0.198 10 false *a 0.115,1.677 0.344,1.875 0.229,0.198 10 false *b 2.771,0.677 3.219,0.875 0.448,0.198 10 false ANT+ 0.677,1.365 1.125,1.563 0.448,0.198 10 false MAIN

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the navigation receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 1 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)



OK

8.CHECK AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

8.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received.




OK

END (AMPLIFIER ANTENNA ASSEMBLY WAS DEFECTIVE)

NG