Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051484 NAVIGATION / MULTI INFO DISPLAY _0248277 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC No. DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected
·

Navigation receiver assembly

·

Combination meter assembly

·

Harness or connector

·

Instrument panel junction block assembly



WIRING DIAGRAM

E302097E02
0.427,1.813 1.917,2.26 1.49,0.448 10 false Combination Meter Assembly 0.427,1.635 0.906,1.844 0.479,0.208 10 false F1 5.469,1.979 6.958,2.427 1.49,0.448 10 false Navigation Receiver Assembly 5.385,0.948 5.708,1.156 0.323,0.208 10 false 17 5.615,1.063 6.094,1.271 0.479,0.208 10 false SPD 5.469,1.781 5.948,1.99 0.479,0.208 10 false F132 1.375,1.063 1.698,1.271 0.323,0.208 10 false +S 1.635,0.938 1.958,1.146 0.323,0.208 10 false 6 2.813,1.052 3.135,1.26 0.323,0.208 10 false 3B 2.813,0.833 3.135,1.042 0.323,0.208 10 false 15 4.156,1.052 4.479,1.26 0.323,0.208 10 false 3A 4.188,0.281 5.25,0.49 1.063,0.208 10 false to each ECU 4.156,0.833 4.479,1.042 0.323,0.208 10 false 16 2.823,1.844 4.5,2.208 1.677,0.365 10 false Instrument Panel Junction Block Assembly

PROCEDURE

1.CHECK SYSTEM SENSORS (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen.

Refer to Check System Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).


b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the Techstream (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).




OK

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U158708E01
1.704,0.478 1.883,0.659 0.179,0.181 10 F1 2.188,1.354 2.705,1.955 false 2.595,1.972 2.820,2.111 0.225,0.139 10 +S 0.097,0.099 0.322,0.238 0.225,0.139 10 *a 1.123,3.88 1.283,4.019 0.161,0.139 10 A 2.784,3.594 3.246,3.733 0.461,0.139 10 GND

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F1-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F1-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
U158719E01
0.125,0.16 0.282,0.316 0.158,0.155 10 *a 2.468,2.206 2.862,2.362 0.394,0.155 10 SPD 2.971,3.717 3.299,3.872 0.328,0.155 10 GND 1.294,4.009 1.505,4.164 0.211,0.155 10 A 2.612,2.154 2.412,1.487 false 1.579,0.237 2.027,0.393 0.448,0.156 10 F132

Check the input waveform.

i.

Remove the navigation receiver assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F132-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F132-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


OK

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION BLOCK)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION BLOCK)
a.

Disconnect the f132 navigation receiver assembly connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F132-17 (SPD) - 3A-16 Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION BLOCK)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the 3B instrument junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-6 (+S) - 3B-15 Always Below 1 Ω




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR