Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2014.07
RM19S0E _56 Audio / Visual / Telematics _051485 PARK ASSIST / MONITORING _0248279 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly*1 or navigation receiver assembly*2 receives a reverse signal from the park/neutral position switch assembly*3 or the back-up light switch assembly*4.

*1: w/o Navigation System

*2: w/ Navigation System

*3: for Automatic Transaxle

*4: for Manual Transaxle


WIRING DIAGRAM

E299059E02
3.292,1.104 3.677,1.281 0.385,0.177 10 false B88 5.833,0.802 6.135,0.979 0.302,0.177 10 false REV 3.302,2.708 3.708,2.875 0.406,0.167 10 false B86 0.229,2.906 2.146,3.24 1.917,0.333 10 false *3: for Automatic Transaxle 0.229,3.271 1.969,3.583 1.74,0.313 10 false *4: for Manual Transaxle 2.26,0.948 2.719,1.219 0.458,0.271 10 false DOME 0.302,0.802 1.563,1.135 1.26,0.333 10 false from Ignition Switch 3.271,2.333 3.427,2.51 0.156,0.177 10 false 2 4.469,2.333 4.625,2.51 0.156,0.177 10 false 1 3.302,0.708 3.458,0.885 0.156,0.177 10 false 2 4.479,0.698 4.635,0.875 0.156,0.177 10 false 1 3.458,0.802 3.667,0.979 0.208,0.177 10 false RB 4.229,0.802 4.469,0.979 0.24,0.177 10 false RL 5.729,2.552 7.115,3.156 1.385,0.604 10 false Radio and Display Receiver Assembly*1 2.833,1.51 3,1.688 0.167,0.177 10 false *4 4.844,1.51 5.01,1.688 0.167,0.177 10 false *4 3.146,0.917 3.313,1.094 0.167,0.177 10 false *3 4.531,0.917 4.698,1.094 0.167,0.177 10 false *3 5.208,0.635 5.365,0.813 0.156,0.177 10 false 2 5.583,0.635 5.74,0.813 0.156,0.177 10 false 2 5.083,0.813 5.521,1.042 0.438,0.229 10 false F132 5.469,0.813 5.865,1.01 0.396,0.198 10 false F127 5.177,0.99 5.375,1.167 0.198,0.177 10 false *2 5.552,0.99 5.75,1.167 0.198,0.177 10 false *1 0.219,2.563 1.906,2.885 1.688,0.323 10 false *2: w/ Navigation System 0.229,2.208 1.979,2.542 1.75,0.333 10 false *1: w/o Navigation System 5.74,3.135 7.125,3.74 1.385,0.604 10 false Navigation Receiver Assembly*2 3.292,1.271 4.74,1.969 1.448,0.698 10 false Park/Neutral Position Switch Assembly*3 3.302,2.885 4.781,3.521 1.479,0.635 10 false Back-up Light Switch Assembly*4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT RECEIVER ASSEMBLY (REVERSE SIGNAL)
a.
U158713E02
2.573,1.74 2.219,1.188 true 2.604,1.708 2.958,1.854 0.354,0.146 10 false REV 1.052,0.188 1.552,0.427 0.5,0.24 10 false F127 2.094,0.177 2.51,0.417 0.417,0.24 10 false F132 1.125,0.427 1.354,0.604 0.229,0.177 10 false *A 2.167,0.417 2.396,0.615 0.229,0.198 10 false *B 0.104,0.042 0.375,0.25 0.271,0.208 10 false *a

Disconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F127-2 (REV) - Body ground*1 Ignition switch ON,
shift lever in not R
Below 1 V
Ignition switch ON,
shift lever in R
11 to 14 V
F132-2 (REV) - Body ground*2 Ignition switch ON,
shift lever in not R
Below 1 V
Ignition switch ON,
shift lever in R
11 to 14 V


Text in Illustration
*A w/o Navigation System
*B w/ Navigation System
*a Rear view of wire harness connector
(to Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2)


c.

Reconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.


*1: w/o Navigation System

*2: w/ Navigation System



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.SYSTEM CHECK
2.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
for Automatic Transaxle A
for Manual Transaxle B



A

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (IG SIGNAL)

B

5.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY (IG SIGNAL)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (IG SIGNAL)
a.
U158699E02
1.823,1.26 1.938,1.906 true 1.573,0.302 1.927,0.521 0.354,0.219 10 false B88 1.854,1.917 2.063,2.094 0.208,0.177 10 false RB 0.135,0.083 0.323,0.26 0.188,0.177 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B88-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


c.

Reconnect the park/neutral position switch assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the F127 radio and display receiver assembly connector*1 or F132 navigation receiver assembly connector*2.


b.

Disconnect the B88 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-2 (REV) - B88-1 (RL)*1 Always Below 1 Ω
F132-2 (REV) - B88-1 (RL)*2
F127-2 (REV) - Body ground*1 Always 10 kΩ or higher
F132-2 (REV) - Body ground*2


Result
Result Proceed to
NG A
OK (for U340E) B
OK (for U441E) C


d.

Reconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.


e.

Reconnect the park/neutral position switch assembly connector.


*1: w/o Navigation System

*2: w/ Navigation System



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

5.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY (IG SIGNAL)
a.
U158530E02
1.604,0.5 1.906,0.698 0.302,0.198 10 false B86 0.135,0.073 0.323,0.25 0.188,0.177 10 false *a

Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B86-2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)


c.

Reconnect the back-up light switch assembly connector.



OK

6.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the F127 radio and display receiver assembly connector*1 or F132 navigation receiver assembly connector*2.


b.

Disconnect the B86 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-2 (REV) - B86-1*1 Always Below 1 Ω
F132-2 (REV) - B86-1*2
F127-2 (REV) - Body ground*1 Always 10 kΩ or higher
F132-2 (REV) - Body ground*2



d.

Reconnect the radio and display receiver assembly connector*1 or navigation receiver assembly connector*2.


e.

Reconnect the back-up light switch assembly connector.


*1: w/o Navigation System

*2: w/ Navigation System



OK

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR