Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248285 CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor) J

NETWORKING  CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "Bus Check".

·

"Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside skid control ECU (brake actuator assembly)

·

Skid control ECU (brake actuator assembly) branch wire or connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

E229243E07
1.427,0.667 1.854,0.833 0.427,0.167 10 false CANH 1.427,1.146 1.854,1.313 0.427,0.167 10 false CANL 0.5,1.604 0.906,1.771 0.406,0.167 10 false A61 4.99,0.594 5.198,0.76 0.208,0.167 10 false 25 5.26,0.688 5.688,0.854 0.427,0.167 10 false CANH 5.26,1.156 5.688,1.323 0.427,0.167 10 false CANL 1.927,2.635 3.302,2.948 1.375,0.313 10 false from IG1 NO. 1 Relay 3.604,2.792 4.542,2.958 0.938,0.167 10 false ECU-IG NO. 2 5.26,3.135 5.688,3.302 0.427,0.167 10 false GND1 4.99,1.031 5.198,1.198 0.208,0.167 10 false 14 1.927,0.594 2.104,0.76 0.177,0.167 10 false 10 1.938,1.031 2.125,1.198 0.188,0.167 10 false 21 5.271,2.625 5.698,2.792 0.427,0.167 10 false IG1 4.99,2.521 5.198,2.688 0.208,0.167 10 false 34 2.333,2.177 3.271,2.49 0.938,0.313 10 false from ALT Fuse 3.729,2.365 4.427,2.531 0.698,0.167 10 false ABS NO. 2 5.26,2.146 5.688,2.313 0.427,0.167 10 false +BS 4.99,2.073 5.198,2.24 0.208,0.167 10 false 12 2.344,1.729 3.281,2.042 0.938,0.313 10 false from ALT Fuse 3.729,1.896 4.448,2.063 0.719,0.167 10 false ABS NO. 1 5.271,1.729 5.698,1.896 0.427,0.167 10 false BM 4.99,1.635 5.198,1.802 0.208,0.167 10 false 24 5.031,3.031 5.24,3.198 0.208,0.167 10 false 1 5.26,3.542 5.688,3.708 0.427,0.167 10 false GND2 4.99,3.448 5.198,3.615 0.208,0.167 10 false 13 0.51,1.781 2.156,2.104 1.646,0.323 10 false NO. 1 Junction Connector 5.073,4.083 6.802,4.75 1.729,0.667 10 false Skid Control ECU (Brake Actuator Assembly) 5.083,3.885 5.479,4.052 0.396,0.167 10 false A55

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
a.
U158541E01
1.133,0.738 1.429,0.895 0.295,0.156 10 A55 0.095,0.067 0.391,0.223 0.295,0.156 10 *a 1.169,2.73 1.588,2.886 0.420,0.156 10 CANH 1.294,1.081 1.714,1.238 0.420,0.156 10 CANL 0.807,2.316 1.126,2.807 false 1.248,1.173 0.807,2.055 false

Disconnect the A55 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A55-25 (CANH) - A55-14 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U158542E01
1.133,0.738 1.429,0.895 0.295,0.156 10 A55 0.095,0.067 0.391,0.223 0.295,0.156 10 *a 1.117,2.75 1.537,2.906 0.420,0.156 10 GND2 1.12,1.051 1.540,1.207 0.420,0.156 10 GND1 0.684,2.234 1.076,2.837 false 1.076,1.119 0.684,1.722 false 2.478,2.75 2.898,2.906 0.420,0.156 10 BM 2.481,1.051 2.901,1.207 0.420,0.156 10 +BS 2.045,2.234 2.436,2.837 false 2.332,2.975 2.751,3.131 0.420,0.156 10 IG1 1.805,2.315 2.29,3.062 false 2.436,1.119 2.045,1.722 false

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A55-12 (+BS) - Body ground Always 11 to 14 V
A55-24 (BM) - Body ground Always 11 to 14 V
A55-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-1 (GND1) - Body ground Always Below 1 Ω
A55-13 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)