Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248290 KEY REMINDER WARNING SYSTEM U

DOOR LOCK  KEY REMINDER WARNING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


U158631E02
1,0.948 1.406,1.188 0.406,0.24 10 false 3D 1.521,3.833 1.927,4.073 0.406,0.24 10 false 3D 4.031,3.833 4.438,4.073 0.406,0.24 10 false 3C 6.083,3.833 6.49,4.073 0.406,0.24 10 false 3E 0.271,0.094 0.677,0.333 0.406,0.24 10 false *1 0.938,6.76 1.344,7 0.406,0.24 10 false *2 3.781,0.792 4.188,1.031 0.406,0.24 10 false MB 3.781,2.854 4.188,3.094 0.406,0.24 10 false MB 0.99,1.594 1.396,1.833 0.406,0.24 10 false 3C 0.979,2.115 1.385,2.354 0.406,0.24 10 false 3E 6.354,0.948 6.76,1.188 0.406,0.24 10 false 3B 1.688,5.208 2.094,5.448 0.406,0.24 10 false 3B 5.438,5.208 5.844,5.448 0.406,0.24 10 false 3A 6.354,1.583 6.76,1.823 0.406,0.24 10 false 3A 3.813,6.448 4.219,6.688 0.406,0.24 10 false F76 3.677,7.5 4.083,7.74 0.406,0.24 10 false F76

Text in Illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU

a.

Remove the main body ECU from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the F76 main body ECU connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
MB-30 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
MB-31 (ALTB) - Body ground None - Body ground Battery power supply Always 11 to 14 V
MB-29 (ACC) - Body ground None - Body ground ACC power supply Ignition switch on (ACC) 11 to 14 V
MB-32 (IG) - Body ground None - Body ground Ignition switch power supply Ignition switch on (IG) 11 to 14 V
F76-17 (KSW) - Body ground Y - Body ground Unlock warning switch input No Key in ignition key cylinder (off) 10 kΩ or higher
Key inserted ignition key cylinder (on) Below 1 Ω


d.

Install the main body ECU to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


e.

Reconnect the F76 main body ECU connector.


f.

Measure the voltage and check for pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-36 (FLCY) - Body ground L - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V
Front door LH closed Pulse generation
F76-17 (KSW) - Body ground Y - Body ground Unlock warning switch input No Key in ignition key cylinder (off) 11 to 14 V
Key inserted ignition key cylinder (on) Below 1 V