Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When the key is inserted into the ignition key cylinder, the antenna coil receives the key code. Then the amplifier amplifies the ID code and outputs it to the transponder key ECU assembly.

·

If this symptom occurs, there may be a communication problem between the transponder key amplifier and the transponder key ECU assembly.


WIRING DIAGRAM

B291391E04
5.375,3.104 6.833,3.49 1.458,0.385 10 false Transponder Key ECU Assembly 0.875,3.104 2.552,3.25 1.677,0.146 10 false Transponder Key Amplifier 5.677,2.458 6.01,2.604 0.333,0.146 10 false GND 3.323,0.479 4.281,0.677 0.958,0.198 10 false from IG2 Relay 3.042,1.948 3.177,2.094 0.135,0.146 10 false 7 3.031,1.542 3.167,1.688 0.135,0.146 10 false 5 3.031,0.771 3.229,0.917 0.198,0.146 10 false 1 3.042,1.167 3.219,1.313 0.177,0.146 10 false 4 5.521,1.958 5.656,2.104 0.135,0.146 10 false 5 5.51,1.573 5.646,1.719 0.135,0.146 10 false 4 5.51,0.396 5.646,0.542 0.135,0.146 10 false 2 4.917,0.604 5.208,0.75 0.292,0.146 10 false IG2 0.875,2.948 1.24,3.094 0.365,0.146 10 false F55 5.375,2.927 5.74,3.073 0.365,0.146 10 false F54 5.677,0.479 5.917,0.625 0.24,0.146 10 false IG 5.688,0.865 6.01,1.01 0.323,0.146 10 false VC5 2.656,0.76 2.979,0.906 0.323,0.146 10 false VC5 5.677,1.26 6.125,1.406 0.448,0.146 10 false CODE 2.552,1.156 3,1.302 0.448,0.146 10 false CODE 5.677,1.656 6.125,1.802 0.448,0.146 10 false TXCT 2.604,1.552 3.052,1.698 0.448,0.146 10 false TXCT 5.677,2.042 6.125,2.188 0.448,0.146 10 false AGND 2.552,1.948 3,2.094 0.448,0.146 10 false AGND 5.458,0.771 5.656,0.917 0.198,0.146 10 false 14 5.438,2.354 5.615,2.5 0.177,0.146 10 false 16 5.448,1.177 5.625,1.323 0.177,0.146 10 false 15 1.698,2.479 2.292,2.625 0.594,0.146 10 false Amplifier 1.24,1 1.677,1.146 0.438,0.146 10 false ANT1 1.229,2.156 1.656,2.302 0.427,0.146 10 false ANT2 0.688,1.458 0.979,1.604 0.292,0.146 10 false Coil

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.

·

Inspection the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
No DTC output A
DTC output B



A

3.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser fuel cut/
OFF or ON
- -

OK:

The item in the Data List indicates "OFF"


Result
Result Proceed to
NG A
OK (for 2NZ-FE) B
OK (for 1NZ-FE) C



A

4.CHECK THEFT WARNING INDICATOR LIGHT OPERATION

B

C

4.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
a.

When the key inserted in ignition key cylinder, check that the theft warning indicator light assembly off.

OK:

The theft warning indicator light assembly off.




OK

NG

5.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
5.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
a.

Perform inspection using a different key that has been registered to the vehicle.


b.

When the key inserted in ignition key cylinder, check that the theft warning indicator light assembly off.

OK:

The theft warning indicator light assembly off.




OK

6.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS

NG

7.CHECK TRANSPONDER KEY AMPLIFIER (VC5 SIGNAL)
6.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
a.

Perform inspection using a different key that has been registered to the vehicle.


b.

It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

B

19.REPLACE KEY
7.CHECK TRANSPONDER KEY AMPLIFIER (VC5 SIGNAL)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158188E02
1.156,1.26 1.156,1.906 false 0.177,2.156 0.417,2.385 0.24,0.229 10 false *b 0.177,0.125 0.417,0.354 0.24,0.229 10 false *a 0.146,3.552 0.479,3.729 0.333,0.177 10 false GND 1.656,0.323 1.917,0.5 0.26,0.177 10 false F55 1.021,1.938 1.323,2.104 0.302,0.167 10 false VC5

Using an oscilloscope, check the waveform.

i.

Waveform

Measurement Condition
Item Content
Tester Connection F55-1 (VC5) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY, IG TERMINAL VOLTAGE)
8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY, IG TERMINAL VOLTAGE)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-1 (VC5) - F54-14 (VC5) Always Below 1 Ω
F55-7 (AGND) - F54-5 (AGND) Always Below 1 Ω
F55-1 (VC5) - Body ground Always 10 kΩ or higher



d.
U158186E02
2.833,1.698 3.156,1.854 0.323,0.156 10 false GND 0.542,1.719 0.74,1.865 0.198,0.146 10 false IG 0.115,0.073 0.313,0.271 0.198,0.198 10 false *a 1.594,0.344 1.865,0.49 0.271,0.146 10 false F54

Reconnect the transponder key amplifier connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-2 (IG) - F54-16 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU assembly)



OK

9.CHECK TRANSPONDER KEY AMPLIFIER (TXCT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TRANSPONDER KEY AMPLIFIER (TXCT SIGNAL)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158193E02
1.948,1.26 1.948,1.969 false 1.667,0.323 1.927,0.5 0.26,0.177 10 false F55 1.813,1.99 2.229,2.167 0.417,0.177 10 false TXCT 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.177,2.177 0.344,2.333 0.167,0.156 10 false *b 0.156,3.521 0.51,3.698 0.354,0.177 10 false GND

Using an oscilloscope, check the waveform.

i.

Waveform

Measurement Condition
Item Content
Tester Connection F55-5 (TXCT) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-5 (TXCT) - F54-4 (TXCT) Always Below 1 Ω
F55-5 (TXCT) - Body ground Always 10 kΩ or higher




OK

11.CHECK TRANSPONDER KEY AMPLIFIER (CODE SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TRANSPONDER KEY AMPLIFIER (CODE SIGNAL)
a.

Disconnect the F55 transponder key amplifier connector.


b.
U158190E02
1.75,1.25 1.75,1.948 false 1.656,0.302 1.917,0.479 0.26,0.177 10 false F55 0.125,3.521 0.479,3.698 0.354,0.177 10 false GND 0.219,0.156 0.385,0.313 0.167,0.156 10 false *a 0.24,2.188 0.406,2.344 0.167,0.156 10 false *b 1.583,1.969 2.01,2.146 0.427,0.177 10 false CODE

Using an oscilloscope, check the waveform.

i.

Waveform

Measurement Condition
Item Content
Tester Connection F55-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F55 transponder key amplifier connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F55-4 (CODE) - F54-15 (CODE) Always Below 1 Ω
F55-4 (CODE) - Body ground Always 10 kΩ or higher



d.

Reconnect the transponder key ECU assembly connector.


e.

Reconnect the transponder key amplifier connector.


f.
U158190E02
1.75,1.25 1.75,1.948 false 1.656,0.302 1.917,0.479 0.26,0.177 10 false F55 0.125,3.521 0.479,3.698 0.354,0.177 10 false GND 0.219,0.156 0.385,0.313 0.167,0.156 10 false *a 0.24,2.188 0.406,2.344 0.167,0.156 10 false *b 1.583,1.969 2.01,2.146 0.427,0.177 10 false CODE

Using an oscilloscope, check the waveform.

i.

Waveform

Measurement Condition
Item Content
Tester Connection F55-4 (CODE) - Body ground
Tool Setting 1 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Front view of wire harness connector
(to Transponder Key Amplifier)
*b Waveform

Result
Result Proceed to
Terminal CODE stuck high (5 V) A
Terminal CODE stuck low (1 V or less) B
Problem in wire harness or connector C




A

13.REPLACE TRANSPONDER KEY AMPLIFIER

B

15.REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY AMPLIFIER
a.


NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE)

NG

15.REPLACE TRANSPONDER KEY ECU ASSEMBLY
15.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).



NEXT

16.REGISTER KEY
16.REGISTER KEY
a.

Register the key (Refer to Service Bulletin).



NEXT

17.REGISTER ECU COMMUNICATION ID
17.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to Service Bulletin).



NEXT

18.CHECK WHETHER ENGINE STARTS
18.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.




OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

19.REPLACE KEY
19.REPLACE KEY
a.

Replace the transponder key master transmitter with a new one (Refer to Service Bulletin).



NEXT

20.REREGISTER KEY
20.REREGISTER KEY
a.

Reregister the key (Refer to Service Bulletin).



NEXT

21.CHECK WHETHER ENGINE STARTS
21.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with an already registered vehicle key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 2NZ-FE) B
NG (for 1NZ-FE) C



A

END (KEY (TRANSPONDER KEY MASTER TRANSMITTER) WAS DEFECTIVE)

B

C