The main body ECU detects the condition of each door courtesy light switch.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RR Door Courtesy SW*1 | Rear door courtesy light switch LH and RH signal /
OFF or ON |
OFF: Rear door LH and RH closed
ON: Rear door LH or RH opened |
- |
| RL Door Courtesy SW*1 | Rear door courtesy light switch LH and RH signal /
OFF or ON |
OFF: Rear door LH and RH closed
ON: Rear door LH or RH opened |
- |
| Back Door Courtesy SW | Back door courtesy light switch signal /
OFF or ON |
OFF: Back door closed
ON: Back door opened |
- |
| FR Door Courtesy | Front door courtesy light switch RH signal /
ON or OFF |
ON: Front door RH closed
OFF: Front door RH opened |
- |
| FL Door Courtesy | Front door courtesy light switch LH signal /
ON or OFF |
ON: Front door LH closed
OFF: Front door LH opened |
- |
*1: for 5 Door
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Front door courtesy light switch assembly LH does not operate) | B |
| NG (Front door courtesy light switch assembly RH does not operate) | C |
| NG (Rear door courtesy light switch assembly does not operate)*1 | D |
| NG (Back door courtesy switch) | E |
*1: for 5 Door
A
B
C
D
E
Inspect the front door courtesy light switch assembly LH (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).
OK
NG
Disconnect the K1 front door courtesy light switch assembly LH connector.
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-1 - 3D-36 | Always | Below 1 Ω |
| K1-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly.
Remove the main body ECU from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-36 - MB-2 (FLCY) | Always | Below 1 Ω |
OK
NG
Inspect the front door courtesy light switch assembly RH (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).
OK
NG
Disconnect K2 front door courtesy light switch assembly RH connector.
Disconnect the F76 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-1 - F76-19 (FRCY) | Always | Below 1 Ω |
| K2-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the rear door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION).
OK
NG
Disconnect K3 or K4 rear door courtesy light switch assembly connector.
Disconnect the F76 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K3-1 - F76-6 (LRCY) | Always | Below 1 Ω |
| K3-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K4-1 - F76-6 (LRCY) | Always | Below 1 Ω |
| K4-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the back door lock assembly (back door courtesy switch) (See page Vehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| NG | A |
| OK (w/ Automatic Light Control System) | B |
| OK (w/o Automatic Light Control System) | C |
A
B
C
w/ Power Door Lock
Disconnect the P12 back door lock assembly (back door courtesy switch) connector.
w/o Power Door Lock
Disconnect the P14 back door lock assembly (back door courtesy switch) connector.
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P12-3 (D+) - 3D-35 | Always | Below 1 Ω |
| P12-3 (D+) - Body ground | Always | 10 kΩ or higher |
| P12-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-4 (D+) - 3D-35 | Always | Below 1 Ω |
| P14-4 (D+) - Body ground | Always | 10 kΩ or higher |
| P14-5 (ACT-) - Body ground | Always | Below 1 Ω |
OK
NG
Remove the instrument panel junction block assembly.
Remove the main body ECU from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-35 - MB-20 (BCTY) | Always | Below 1 Ω |
OK
NG
w/ Power Door Lock
Disconnect the P12 back door lock assembly (back door courtesy switch) connector.
w/o Power Door Lock
Disconnect the P14 back door lock assembly (back door courtesy switch) connector.
Disconnect the F76 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P12-3 (D+) - F76-1 (BCTY) | Always | Below 1 Ω |
| P12-3 (D+) - Body ground | Always | 10 kΩ or higher |
| P12-2 (ACT-) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-4 (D+) - F76-1 (BCTY) | Always | Below 1 Ω |
| P14-4 (D+) - Body ground | Always | 10 kΩ or higher |
| P14-5 (ACT-) - Body ground | Always | Below 1 Ω |
OK
NG