Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051492 LIGHTING (INT) _0248303 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU controls the map light assembly.

WIRING DIAGRAM

E232059E01
3.71,2.534 3.907,2.686 0.198,0.152 10 3B 5.548,2.535 5.777,2.685 0.229,0.149 10 MB 3.71,1.383 3.907,1.553 0.198,0.170 10 3A 3.756,2.346 3.862,2.516 0.106,0.170 10 6 4.075,3.211 5.702,3.523 1.627,0.312 10 Instrument Panel Junction Block Assembly 1.26,0.767 2.048,0.940 0.788,0.173 10 from Battery 5.773,4.064 6.790,4.215 1.017,0.151 10 Main Body ECU 3.71,0.771 3.907,0.940 0.198,0.170 10 3C 5.61,2.346 5.716,2.516 0.106,0.170 10 1 3.756,1.2 3.862,1.370 0.106,0.170 10 5 3.756,0.58 3.862,0.750 0.106,0.170 10 4 1.289,3.829 1.464,3.987 0.175,0.158 10 L9 1.289,3.992 2.563,4.155 1.274,0.163 10 Map Light Assembly 2.701,0.917 3.138,1.066 0.437,0.149 10 DOME 5.909,2.534 6.139,2.686 0.231,0.152 10 ILE 2.919,2.444 3.025,2.614 0.106,0.170 10 2 2.919,3.239 3.025,3.409 0.106,0.170 10 1 0.806,2.707 0.911,2.876 0.106,0.170 10 3 0.967,2.712 1.086,2.871 0.119,0.158 10 B 2.564,2.45 2.859,2.608 0.295,0.158 10 CTY 2.746,3.245 2.861,3.403 0.115,0.158 10 E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Turn the map light assembly switch to the DOOR position.


e.

All doors closed (door courtesy light switches OFF).


f.

Enter the following menus: Body / Main Body / Active Test.


g.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Map light assembly OFF or ON Map light switch at DOOR position and all doors closed.

OK:

The illuminated entry system operates normally when operating it through the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Inspect the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
U158599E02
0.104,0.052 0.271,0.208 0.167,0.156 10 false *a 1.635,0.219 1.833,0.396 0.198,0.177 10 false 3C

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-4 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the L9 map light assembly connector.


b.

Disconnect the 3A and 3B instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L9-3 (B) - 3A-5 Always Below 1 Ω
L9-2 (CTY) - 3B-6 Always Below 1 Ω
L9-3 (B) - Body ground Always 10 kΩ or higher
L9-2 (CTY) - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U158600E01
0.119,0.083 0.289,0.243 0.170,0.161 10 *a 1.699,0.235 1.886,0.416 0.187,0.181 10 3A 1.703,1.547 1.890,1.729 0.187,0.181 10 3B 5.225,0.23 5.419,0.412 0.195,0.181 10 3C 5.154,1.578 5.379,1.759 0.225,0.181 10 MB 3.56,2.252 3.799,2.411 0.239,0.159 10 ILE 3.628,2.063 3.665,2.242 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-4 - 3A-5 Always Below 1 Ω
3B-6 - MB-1 (ILE) Always Below 1 Ω




OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY