Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM U

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


U127301E02
2.198,0.448 2.438,0.625 0.24,0.177 10 false F1 5.146,0.448 5.385,0.625 0.24,0.177 10 false F3

a.

Disconnect the F1 combination meter assembly connector.


b.

Measure the voltage and resistance of the wire harness side connector.

Terminals No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-21 (ET) - Body ground W-B - Body ground Ground Always Below 1 Ω
F1-39 (IG+) - Body ground P - Body ground Ignition switch signal Ignition switch off → ON Below 1 V → 11 to 14 V
F1-40 (B) - Body ground L - Body ground Battery Always 11 to 14 V
F3-1 (B) - Body ground R - Body ground Battery Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the F1 combination meter assembly connector.


d.

Measure the resistance, voltage and check for pulse of the wire harness side connector.

Terminals No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-5 (SI) - Body ground L - Body ground Speed signal (Input) Driving at approximately
20 km/h (12 mph)
Pulse generation
(See waveform 1)
F1-6 (+S) - Body ground SB - Body ground Speed signal (Output) Driving at approximately
20 km/h (12 mph)
Pulse generation
(See waveform 1)
F1-7 (P/SB) - Body ground P - Body ground Front seat inner belt assembly signal (passenger side) Front passenger seat is occupied and its seat belt is unfastened → fastened Below 1 V → 11 to 14 V
F1-9 (S) - Body ground Y - Body ground Engine oil pressure signal Engine oil pressure warning light ON → OFF Below 1 V → 11 to 14 V
F1-11 (CHK) - Body ground LG - Body ground Check engine warning light signal Check engine warning light ON → OFF Below 1 V → 11 to 14 V
F1-12 (SW) - Body ground GR - Body ground Brake fluid level warning light signal Ignition switch ON
Brake fluid level warning light ON → OFF
Below 1 V → 11 to 14 V
F1-14 (-) - Body ground BR - Body ground High beam indicator signal (-) Always Below 1 V
F1-16 (L) - Body ground G - Body ground Fuel level signal Ignition switch ON
Fuel level is FULL → EMPTY
Below 1 V → 4.5 to 9.0 V
F1-19 (+) - Body ground GR - Body ground High beam indicator signal (+) High beam indicator ON → OFF 11 to 14 V → Below 1 V
F1-20 (ILL+) - Body ground R - Body ground Taillight signal Light control switch OFF → ON Below 1 V → 11 to 14 V
F1-31 (CANL) - Body ground W - Body ground CAN communication line Ignition switch ON Pulse generation
F1-32 (CANH) - Body ground G - Body ground CAN communication line Ignition switch ON Pulse generation
F3-3 (HAZ) - Body ground L - Body ground Hazard warning signal switch signal Hazard warning signal switch off 11 to 14 V
Hazard warning signal switch on Below 1 Ω
F3-7 (LR) - Body ground V - Body ground Right turn signal Ignition switch ON
Right turn indicator light OFF → ON
Below 1 V → 11 to 14 V
F3-9 (ER) - Body ground B - Body ground Turn signal switch RH signal Turn signal switch RH on 11 to 14 V
Turn signal switch RH off Below 1 Ω
F3-10 (EL) - Body ground Y - Body ground Turn signal switch LH signal Turn signal switch LH on 11 to 14 V
Turn signal switch LH off Below 1 Ω
F3-12 (FOG)*1 - Body ground BE - Body ground Front fog signal Ignition switch ON
Front fog switch OFF → ON
Below 1 V → 11 to 14 V
F3-13 (LL) - Body ground LG - Body ground Left turn signal Ignition switch ON
Left turn indicator light OFF → ON
Below 1 V → 11 to 14 V

*1: w/ Fog Light


If the result is not as specified, the combination meter assembly may have a malfunction.

i.
E346306E01
2.844,1.208 3.271,1.396 0.427,0.188 10 false GND

Waveform 1: Using an oscilloscope

Item Condition
Terminal Connections F1-6 (+S) and Body ground
F1-5 (SI) and Body ground
Tool Setting 5 V/DIV, 20 ms/DIV
Condition Driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the cycle of the signal waveform narrows.





CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


U127318E02
0.979,0.948 1.25,1.104 0.271,0.156 10 false 3D 1.521,3.833 1.729,4 0.208,0.167 10 false 3D 4.021,3.823 4.26,4 0.24,0.177 10 false 3C 5.865,3.823 6.104,4 0.24,0.177 10 false 3E 6.323,3.833 6.542,4 0.219,0.167 10 false 3F 0.271,0.094 0.677,0.333 0.406,0.24 10 false *1 0.927,6.656 1.333,6.896 0.406,0.24 10 false *2 0.531,2.406 0.792,2.646 0.26,0.24 10 false *A 0.979,2.396 1.24,2.635 0.26,0.24 10 false *B 5.844,3.542 6.104,3.729 0.26,0.188 10 false *A 6.281,3.542 6.542,3.729 0.26,0.188 10 false *B 3.771,0.792 4.063,0.948 0.292,0.156 10 false MB 3.781,2.854 4.052,3.01 0.271,0.156 10 false MB 0.99,1.583 1.208,1.76 0.219,0.177 10 false 3C 1,2.104 1.208,2.25 0.208,0.146 10 false 3F 0.542,2.115 0.792,2.271 0.25,0.156 10 false 3E 6.365,0.948 6.615,1.115 0.25,0.167 10 false 3B 1.677,5.208 1.896,5.406 0.219,0.198 10 false 3B 5.438,5.198 5.656,5.385 0.219,0.188 10 false 3A 6.365,1.573 6.625,1.74 0.26,0.167 10 false 3A 3.813,6.448 4.073,6.615 0.26,0.167 10 false F76 3.677,7.49 3.969,7.688 0.292,0.198 10 false F76

Text in Illustration
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU
(Multiplex Network Body ECU)

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground None - Body ground Ignition power supply (ACC signal) Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground None - Body ground +B (power system signal system) power supply Always 11 to 14 V
MB-31 (ALTB) - Body ground None - Body ground +B (power system alternator system) power supply Always 11 to 14 V
MB-32 (IG) - Body ground None - Body ground Ignition power supply (IG signal) Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Install the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


d.

Measure the voltage and check for pulse between each terminal of the wire harness side connectors and body ground.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3A-28 (PKB) - Body ground R - Body ground Parking brake signal Parking brake warning light ON → OFF Below 1 V → 11 to 14 V
3D-34 (DBKL) - Body ground W - Body ground Front seat inner belt assembly signal (driver side) Driver seat belt warning light OFF → ON Below 1 V → 11 to 14 V
F76-13 (CANL) - Body ground W - Body ground CAN communication line Ignition switch ON Pulse generation
F76-14 (CANH) - Body ground R - Body ground CAN communication line Ignition switch ON Pulse generation

If the result is not as specified, there may be a malfunction in the wire harness.



COMBINATION METER INTERNAL CIRCUIT


U158672E02
2.521,0.865 2.875,1.031 0.354,0.167 10 false I/F 2.49,2.698 2.792,2.865 0.302,0.167 10 false I/F 2.49,3.24 2.792,3.406 0.302,0.167 10 false I/F 2.302,1.583 2.625,1.75 0.323,0.167 10 false I/F 2.125,2.104 2.375,2.271 0.25,0.167 10 false I/F 1.74,0.875 2.229,1.052 0.49,0.177 10 false Buzzer 3.927,0.719 4.281,0.885 0.354,0.167 10 false I/F 3.115,4.479 3.479,4.635 0.365,0.156 10 false CPU 4.031,2.698 4.938,2.99 0.906,0.292 10 false Display Driver 4.042,1.729 4.948,2.021 0.906,0.292 10 false Display Driver 4.323,5.719 4.823,5.917 0.5,0.198 10 false DOOR 4.438,6.917 4.802,7.115 0.365,0.198 10 false EPS 3.792,1.271 4.802,1.583 1.01,0.313 10 false ILLUMINATION 4.271,7.552 4.896,7.75 0.625,0.198 10 false AIRBAG 1.854,5.844 2.156,6.01 0.302,0.167 10 false I/F 1.854,7.208 2.156,7.375 0.302,0.167 10 false I/F 0.042,6.948 0.865,7.125 0.823,0.177 10 false F1-7 (P/SB) 1.854,6.323 2.115,6.49 0.26,0.167 10 false I/F 3.844,4.063 4.313,4.24 0.469,0.177 10 false 5 V IC 6.198,0.542 7.052,0.719 0.854,0.177 10 false F1-20 (ILL+) 6.219,4.042 7.073,4.219 0.854,0.177 10 false F1-40 (B) 6.208,4.625 7.063,4.802 0.854,0.177 10 false F1-39 (IG+) 3.958,8.042 4.719,8.271 0.76,0.229 10 false LED Driver 0.188,1.875 0.823,2.052 0.635,0.177 10 false F1-16 (L) 0.115,5.094 0.844,5.271 0.729,0.177 10 false F1-21 (ET) 0.219,5.625 0.833,5.802 0.615,0.177 10 false F1-5 (SI) 0.188,6.115 0.823,6.292 0.635,0.177 10 false F1-6 (+S) 1.396,2.677 2.167,3 0.771,0.323 10 false Trip Switch 1.323,3.198 2.208,3.583 0.885,0.385 10 false Clock Switch Drive Monitor 6.219,2.479 7.135,2.656 0.917,0.177 10 false F3-1 (B) 6.208,7.656 7.125,7.833 0.917,0.177 10 false F3-13 (LL) 6.208,7.323 7.125,7.5 0.917,0.177 10 false F3-7 (LR) 6.208,6.99 7.125,7.167 0.917,0.177 10 false F3-3 (HAZ) 6.208,6.677 7.125,6.854 0.917,0.177 10 false F3-9 (ER) 6.208,6.344 7.125,6.521 0.917,0.177 10 false F3-10 (EL)

U158673E02
4.938,1.271 5.281,1.458 0.344,0.188 10 false ABS 4.844,1.896 5.479,2.104 0.635,0.208 10 false D BELT 4.688,2.5 5.531,2.719 0.844,0.219 10 false SLIP OFF*1 4.875,3.104 5.417,3.313 0.542,0.208 10 false SLIP*1 4.698,3.688 5.5,3.896 0.802,0.208 10 false TEMP HOT 4.677,4.281 5.573,4.51 0.896,0.229 10 false TEMP COOL 2.302,3.625 2.656,4.042 0.354,0.417 10 false CAN I/F 3.052,2.99 3.573,3.177 0.521,0.188 10 false 5 V +B 2.458,4.448 3.438,4.823 0.979,0.375 10 false CAN Controller 3.646,2.448 3.979,2.604 0.333,0.156 10 false CPU 4.479,0.104 5.344,0.438 0.865,0.333 10 false LED Driver 4.698,7.302 5.521,7.552 0.823,0.25 10 false TRC OFF*1 0.406,3.625 1.344,3.802 0.938,0.177 10 false F1-32 (CANH) 0.427,4.104 1.354,4.281 0.927,0.177 10 false F1-31 (CANL) 0.5,9.438 2.719,9.76 2.219,0.323 10 false *2: w/o Tachometer 0.5,9.083 2.719,9.406 2.219,0.323 10 false *1: w/ VSC 4.792,8.573 5.438,8.854 0.646,0.281 10 false FUEL*2

E231152E02
4.49,0.25 5.208,0.573 0.719,0.323 10 false LED Driver 4.854,6.677 5.417,7 0.563,0.323 10 false TURN L 4.854,6.073 5.406,6.292 0.552,0.219 10 false TURN R 4.771,1.281 5.573,1.521 0.802,0.24 10 false 120 km/h*2 4.781,2.49 5.469,2.813 0.688,0.323 10 false CRUISE*1 4.917,1.896 5.396,2.083 0.479,0.188 10 false SET*1 2.448,8.188 4.448,8.51 2,0.323 10 false *2: w/ Speed Warning Function 0.198,8.188 2.021,8.51 1.823,0.323 10 false *1: w/ Cruise Control System

U158674E02
3.188,1.271 3.469,1.604 0.281,0.333 10 false MIL 3.073,1.875 3.583,2.208 0.51,0.333 10 false BRAKE 3.021,2.479 3.677,2.813 0.656,0.333 10 false CHARGE 2.708,4.302 3.906,4.635 1.198,0.333 10 false OIL PRESSURE 3.104,5.5 3.688,5.833 0.583,0.333 10 false BEAM 2.885,6.104 3.938,6.438 1.052,0.333 10 false FRONT FOG*1 6.313,5.198 7.052,5.417 0.74,0.219 10 false F1-19 (+) 6.302,5.781 7.125,6.031 0.823,0.25 10 false F1-12 (FOG) 0.094,0.969 0.917,1.146 0.823,0.177 10 false F1-11 (CHK) 0.167,1.583 0.958,1.76 0.792,0.177 10 false F1-12 (SW) 0.063,2.177 0.948,2.354 0.885,0.177 10 false F1-13 (CHG-) 0.302,3.99 0.885,4.271 0.583,0.281 10 false F1-9 (S) 0.292,5.188 0.917,5.396 0.625,0.208 10 false F1-14 (-) 4.063,0.396 4.927,0.729 0.865,0.333 10 false LED Driver 0.188,8.271 2.479,8.594 2.292,0.323 10 false *1: w/ Fog Light

Connectors
Terminal No. Wire Harness Side
F1 5 Brake actuator assembly (Skid control ECU)*1 or Speedometer sensor*2
6 Other ECU
7 Occupant detection sensor and Front seat inner belt assembly (Front passenger side)
9 Engine oil pressure switch assembly
11 ECM
12 Brake fluid level warning switch
14 Body ground
16 Fuel sender gauge assembly
19 H-LP LH HI fuse
20 Panel fuse
21 Body ground
31 CAN communication line
32 CAN communication line
39 IG2 relay
40 Battery
F3 1 Battery
3 Hazard warning signal switch assembly
7 Turn signal light RH
9 Headlight dimmer switch assembly (Turn signal switch)
10 Headlight dimmer switch assembly (Turn signal switch)
12 FR FOG relay*3
13 Turn signal light LH

*1: w/ ABS

*2: w/o ABS

*3: w/ Fog Light