Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter assembly controls the fuel receiver gauge in accordance with the resistance of the fuel sender gauge, which varies depending on the amount of fuel remaining in the fuel tank.


WIRING DIAGRAM

E219770E13
0.521,2.604 0.865,2.802 0.344,0.198 10 false K17 0.521,2.771 3.771,3.094 3.25,0.323 10 false Fuel Suction with Pump and Gauge Tube Assembly 3.51,1.198 3.781,1.375 0.271,0.177 10 false FS 3.51,1.604 3.781,1.781 0.271,0.177 10 false FE 2.49,1.208 2.708,1.365 0.219,0.156 10 false 2 3.844,1.208 4.063,1.365 0.219,0.156 10 false 2 2.49,1.594 2.708,1.75 0.219,0.156 10 false 1 3.844,1.594 4.063,1.75 0.219,0.156 10 false 3 5.188,1.302 5.406,1.458 0.219,0.156 10 false L 4.885,1.219 5.125,1.396 0.24,0.177 10 false 16 4.792,2.906 5.125,3.063 0.333,0.156 10 false F1 4.792,3.063 6.656,3.385 1.865,0.323 10 false Combination Meter Assembly 0.792,2.073 2.719,2.396 1.927,0.323 10 false Fuel Sender Gauge Assembly

PROCEDURE

1.CONFIRM DTC OUTPUT
a.

Check DTC (See page ).

Result
Result Proceed to
DTC B1500 is not output A
DTC B1500 is output B



A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F Vehicle is stopped and the engine idling.

OK:

Fuel receiver gauge indication is normal.




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.



b.

Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


A

4.CHECK FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.CHECK FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E158805E09
0.217,0.108 0.975,0.292 0.758,0.184 10 *a 2.507,0.547 2.753,0.710 0.246,0.163 10 FS 0.427,1.2 0.673,1.363 0.246,0.163 10 FE 1.355,1.278 0.745,1.278 false 1.836,1.217 2.425,0.629 false 0.615,0.656 1.411,0.821 0.796,0.165 10 *b 0.615,3.098 1.411,3.263 0.796,0.165 10 *c

Remove the fuel suction with pump and gauge tube assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly)
*b Connector A
*c Connector B

Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


c.

Reinstall the fuel suction with pump and gauge tube assembly.



A

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)

B

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the K17 fuel suction with pump and gauge tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-16 (L) - K17-2 (FS) Always Below 1 Ω
F1-16 (L) - Body ground Always 10 kΩ or higher
K17-3 (FE) - Body ground Always Below 1 Ω



d.

Reconnect the fuel suction with pump and gauge tube assembly connector.


e.

Reconnect the combination meter assembly connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR