Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is output when the combination meter assembly detects a fuel sender gauge malfunction.

DTC No. DTC Detection Condition Trouble Area
B1500 When combination meter detects fuel sender gauge malfunction
·

Harness or connector

·

Combination meter assembly

·

Fuel suction with pump and gauge tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

E219770E12
0.521,2.615 0.854,2.771 0.333,0.156 10 false K17 0.521,2.781 3.771,3.104 3.25,0.323 10 false Fuel Suction with Pump and Gauge Tube Assembly 3.531,1.219 3.781,1.375 0.25,0.156 10 false FS 3.531,1.604 3.76,1.76 0.229,0.156 10 false FE 2.49,1.208 2.708,1.365 0.219,0.156 10 false 2 3.844,1.219 4.063,1.375 0.219,0.156 10 false 2 2.479,1.594 2.698,1.75 0.219,0.156 10 false 1 3.844,1.604 4.063,1.76 0.219,0.156 10 false 3 5.188,1.333 5.406,1.49 0.219,0.156 10 false L 4.906,1.208 5.125,1.385 0.219,0.177 10 false 16 4.792,2.896 5.125,3.052 0.333,0.156 10 false F1 4.792,3.052 6.656,3.375 1.865,0.323 10 false Combination Meter Assembly 0.792,2.063 2.719,2.385 1.927,0.323 10 false Fuel Sender Gauge Assembly

PROCEDURE

1.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.



b.

Inspect fuel sender gauge assembly.


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E158805E09
0.217,0.108 0.975,0.292 0.758,0.184 10 *a 2.507,0.547 2.753,0.710 0.246,0.163 10 FS 0.427,1.2 0.673,1.363 0.246,0.163 10 FE 1.355,1.278 0.745,1.278 false 1.836,1.217 2.425,0.629 false 0.615,0.656 1.411,0.821 0.796,0.165 10 *b 0.615,3.098 1.411,3.263 0.796,0.165 10 *c

Remove the fuel suction with pump and gauge tube assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly)
*b Connector A
*c Connector B

Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


c.

Reinstall the fuel suction with pump and gauge tube assembly.



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)

B

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the K17 fuel suction with pump and gauge tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-16 (L) - K17-2 (FS) Always Below 1 Ω
F1-16 (L) - Body ground Always 10 kΩ or higher
K17-3 (FE) - Body ground Always Below 1 Ω



d.

Reconnect the fuel suction with pump and gauge tube assembly connector.


e.

Reconnect the combination meter assembly connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR