Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

The combination meter assembly receives headlight dimmer switch information signals, and flash the turn signal lights.

DTC No. DTC Detection Trouble Area
B1507 When IG voltage is 9.5 V or more and the following condition detected:
1.

Open in turn signal light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly


B1508 When IG voltage is 9.5 V or more and the following condition detected:
1.

Short in turn signal light circuit or hazard warning light circuit


·

Harness or connector

·

Bulb

·

Instrument panel junction block assembly

·

Combination meter assembly



WIRING DIAGRAM

E226983E02
4.988,5.215 6.837,5.360 1.849,0.145 10 Combination Meter Assembly 4.988,5.047 5.191,5.192 0.203,0.145 10 F3 5.538,0.721 5.741,0.867 0.203,0.145 10 LL 5.268,0.623 5.472,0.768 0.203,0.145 10 13 5.538,4.49 5.741,4.635 0.203,0.145 10 LR 5.31,4.392 5.514,4.537 0.203,0.145 10 7 4.634,4.313 4.838,4.458 0.203,0.145 10 25 4.634,4.481 4.838,4.626 0.203,0.145 10 3B 4.634,0.544 4.838,0.689 0.203,0.145 10 24 4.634,0.712 4.838,0.857 0.203,0.145 10 3B 3.053,5.663 3.256,5.808 0.203,0.145 10 5 3.011,5.831 3.214,5.976 0.203,0.145 10 3D 3.011,0.549 3.214,0.694 0.203,0.145 10 28 3.011,0.717 3.214,0.862 0.203,0.145 10 3C 3.011,1.782 3.214,1.927 0.203,0.145 10 18 3.011,1.95 3.214,2.095 0.203,0.145 10 3D 3.011,3.043 3.214,3.188 0.203,0.145 10 29 3.011,3.211 3.214,3.356 0.203,0.145 10 3C 3.011,4.318 3.214,4.463 0.203,0.145 10 38 3.011,4.486 3.214,4.631 0.203,0.145 10 3C 3.011,6.966 3.214,7.111 0.203,0.145 10 37 3.011,7.134 3.214,7.279 0.203,0.145 10 3C 3.12,7.778 4.779,8.099 1.660,0.321 10 Instrument Panel Junction Block Assembly 0.696,1.095 1.001,1.278 0.305,0.184 10 A8 0.696,1.263 2.390,1.584 1.694,0.321 10 Front Turn Signal Light LH 0.817,0.641 0.937,0.786 0.120,0.145 10 2 2.19,0.641 2.394,0.786 0.203,0.145 10 1 0.752,2.328 1.057,2.511 0.305,0.184 10 K37 0.752,2.496 2.419,2.817 1.667,0.321 10 Rear Turn Signal Light LH 1.027,7.058 1.186,7.203 0.158,0.145 10 E 1.98,7.058 2.138,7.203 0.158,0.145 10 B 0.817,7.058 0.937,7.203 0.120,0.145 10 2 2.19,7.058 2.394,7.203 0.203,0.145 10 1 1.027,3.135 1.186,3.280 0.158,0.145 10 E 1.98,3.135 2.138,3.280 0.158,0.145 10 B 0.817,1.874 0.937,2.019 0.120,0.145 10 6 2.19,1.874 2.394,2.019 0.203,0.145 10 2 0.402,3.589 0.707,3.772 0.305,0.184 10 A73 0.402,3.757 2.714,4.078 2.312,0.321 10 Side Turn Signal Light Assembly LH 0.817,3.135 0.937,3.280 0.120,0.145 10 2 2.19,3.135 2.394,3.280 0.203,0.145 10 1 0.696,4.85 1.001,5.033 0.305,0.184 10 A7 0.696,5.018 2.390,5.339 1.694,0.321 10 Front Turn Signal Light RH 0.817,4.396 0.937,4.541 0.120,0.145 10 2 2.19,4.396 2.394,4.541 0.203,0.145 10 1 0.752,6.209 1.057,6.392 0.305,0.184 10 K38 0.752,6.377 2.419,6.698 1.667,0.321 10 Rear Turn Signal Light RH 0.817,5.755 0.937,5.900 0.120,0.145 10 6 2.19,5.755 2.394,5.900 0.203,0.145 10 2 0.402,7.512 0.707,7.695 0.305,0.184 10 A72 0.402,7.68 2.714,8.001 2.312,0.321 10 Side Turn Signal Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect each turn signal light illumination.


Result
Result Proceed to
One side of the turn signal lights does not illuminate. A
Front turn signal lights do not illuminate. B
Rear turn signal lights do not illuminate. C
Side turn signal lights do not illuminate. D


A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (REAR TURN SIGNAL LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F3 combination meter assembly connector.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F3-13 (LL) - 3B-24 Always Below 1 Ω
F3-13 (LL) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F3-7 (LR) - 3B-25 Always Below 1 Ω
F3-7 (LR) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
NG A
OK B


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A7*1 or A8*2 front turn signal light connector.

*1: for RH

*2: for LH



b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A8-1 - 3C-28 Always Below 1 Ω
A8-2 - Body ground Always Below 1 Ω
A8-1 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A7-1 - 3C-38 Always Below 1 Ω
A7-2 - Body ground Always Below 1 Ω
A7-1 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (REAR TURN SIGNAL LIGHT - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the K38*1 or K37*2 rear turn signal light connector.

*1: for RH

*2: for LH



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
K37-2 - 3D-18 Always Below 1 Ω
K37-6 -Body ground Always Below 1 Ω
K37-2 -Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
K38-2 - 3D-5 Always Below 1 Ω
K38-6 -Body ground Always Below 1 Ω
K38-2 -Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A72*1 or A73*2 side turn signal light assembly connector.

*1: for RH

*2: for LH



b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A73-1 (B) - 3C-29 Always Below 1 Ω
A73-2 (E) -Body ground Always Below 1 Ω
A73-1 (B) -Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A72-1 (B) - 3C-37 Always Below 1 Ω
A72-2 (E) -Body ground Always Below 1 Ω
A72-1 (B) -Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-25 - 3C-38 Always Below 1 Ω
3B-25 - 3D-5 Always Below 1 Ω
3B-25 - 3C-37 Always Below 1 Ω
3B-24 - 3C-28 Always Below 1 Ω
3B-24 - 3D-18 Always Below 1 Ω
3B-24 - 3C-29 Always Below 1 Ω




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY