Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag sensor assembly, spiral cable sub-assembly and steering pad.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC No. DTC Detection Condition Trouble Area
B1800/51
·

The airbag sensor assembly receives a line short circuit signal in the driver side squib circuit during primary check.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Airbag sensor assembly


B1801/51
·

The airbag sensor assembly receives an open circuit signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag sensor assembly malfunction


B1802/51
·

The airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag sensor assembly malfunction


B1803/51
·

The airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit.

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C241678E04
4.74,4.693 5.104,4.845 0.364,0.151 10 F16 4.74,4.869 6.313,5.015 1.573,0.147 10 Airbag Sensor Assembly 2.779,3.559 3.045,3.710 0.266,0.151 10 F17 3.254,2.118 3.530,2.269 0.276,0.151 10 D+ 3.254,2.964 3.505,3.116 0.251,0.151 10 D- 4.789,2.221 5.079,2.372 0.290,0.151 10 D+ 4.789,3.065 5.035,3.216 0.246,0.151 10 D- 2.481,2.132 2.580,2.283 0.099,0.151 10 2 2.476,2.977 2.575,3.128 0.099,0.151 10 1 4.57,2.977 4.670,3.128 0.099,0.151 10 6 4.57,2.133 4.670,2.284 0.099,0.151 10 5 2.779,3.735 4.496,3.936 1.717,0.201 10 Spiral Cable Sub-assembly 0.757,3.762 1.972,4.111 1.216,0.349 10 Steering Pad (Driver Side Squib) 0.757,3.587 0.923,3.738 0.166,0.151 10 z1 3.591,2.964 3.691,3.116 0.099,0.151 10 2 3.591,2.118 3.691,2.269 0.099,0.151 10 1 2.123,2.118 2.413,2.269 0.290,0.151 10 D+ 2.137,2.963 2.383,3.114 0.246,0.151 10 D-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C167973E07
1.906,0.688 2.021,1.698 false 0.323,2.74 0.208,1.865 false 0.365,2.677 0.531,2.854 0.167,0.177 10 false *1 1.729,0.573 1.938,0.74 0.208,0.167 10 false *4 0.948,2.188 1.115,2.354 0.167,0.167 10 false *2 2.698,2.271 2.875,2.469 0.177,0.198 10 false *3 1.708,1.917 1.833,2.094 0.125,0.177 10 false C 2.125,1.917 2.25,2.094 0.125,0.177 10 false B 2.448,1.667 2.573,1.844 0.125,0.177 10 false A 1.521,1.917 1.646,2.094 0.125,0.177 10 false D 0.51,1.927 0.635,2.104 0.125,0.177 10 false E 0.302,1.938 0.427,2.115 0.125,0.177 10 false F

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the steering pad, spiral cable sub-assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the steering pad, spiral cable sub-assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Steering Pad (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire



OK

2.CHECK STEERING PAD (DRIVER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK STEERING PAD (DRIVER SIDE SQUIB)
SST
09843-18061  

a.
U158418E02
2.198,2.333 2.385,2.333 false 0.354,0.844 0.229,1.271 false 0.854,2.542 1.094,2.719 0.24,0.177 10 false z1 0.458,0.906 0.563,1.063 0.104,0.156 10 false F 0.646,0.906 0.771,1.063 0.125,0.156 10 false E 1.76,0.917 1.885,1.073 0.125,0.156 10 false D 1.875,0.917 2,1.073 0.125,0.156 10 false C 0.906,1.208 1.083,1.385 0.177,0.177 10 false *2 0.125,1.292 0.281,1.469 0.156,0.177 10 false *1 2.333,1.26 2.51,1.406 0.177,0.146 10 false *3 0.531,1.865 0.708,2.031 0.177,0.167 10 false *a 0.844,2.313 1.021,2.479 0.177,0.167 10 false *4 2.427,2.26 2.719,2.417 0.292,0.156 10 false SST

Connect the instrument panel wire to the airbag sensor assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


Text in Illustration
*1 Steering Pad (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector E
*a Front view of wire harness connector
(to Steering Pad (Driver Side Squib))

HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK DRIVER SIDE SQUIB CIRCUIT
3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
U158375E02
1.625,2.292 1.292,2.635 true 1.813,2.302 2.115,2.615 true 0.344,0.781 0.563,0.333 false 0.594,0.229 0.75,0.385 0.156,0.156 10 false *1 2.344,1.344 2.5,1.5 0.156,0.156 10 false *3 0.427,1 0.531,1.156 0.104,0.156 10 false F 0.625,1 0.74,1.146 0.115,0.146 10 false E 1.646,0.979 1.771,1.146 0.125,0.167 10 false D 1.771,0.979 1.896,1.125 0.125,0.146 10 false C 2.135,0.979 2.25,1.125 0.115,0.146 10 false B 2.5,0.76 2.625,0.917 0.125,0.156 10 false A 0.854,1.25 1.01,1.406 0.156,0.156 10 false *2 0.458,1.688 0.615,1.844 0.156,0.156 10 false *a 0.906,1.885 1.063,2.042 0.156,0.156 10 false *4 1.146,2.625 1.375,2.781 0.229,0.156 10 false D- 0.906,2.115 1.135,2.271 0.229,0.156 10 false z1 2.146,2.615 2.375,2.771 0.229,0.156 10 false D+

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z1-2 (D+) - Body ground Ignition switch ON Below 1 V
z1-1 (D-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - Body ground Always 1 MΩ or higher
z1-1 (D-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always 1 MΩ or higher


Text in Illustration
*1 Steering Pad (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Connector E
*a Front view of wire harness connector
(to Steering Pad (Driver Side Squib))




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the steering pad and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.
U158376E02
1.521,2.604 1.229,2.885 true 1.677,2.604 2,2.885 true 2.042,0.875 1.896,0.25 false 0.271,0.906 0.448,0.375 false 0.333,1.125 0.438,1.281 0.104,0.156 10 false F 0.531,1.125 0.656,1.281 0.125,0.156 10 false E 1.563,1.115 1.688,1.271 0.125,0.156 10 false D 1.771,1.115 1.896,1.271 0.125,0.156 10 false C 2.146,1.115 2.271,1.271 0.125,0.156 10 false B 2.5,0.875 2.625,1.031 0.125,0.156 10 false A 0.771,1.344 0.938,1.521 0.167,0.177 10 false *2 0.49,0.26 0.677,0.438 0.188,0.177 10 false *1 1.719,0.167 1.896,0.302 0.177,0.135 10 false *4 2.385,1.458 2.552,1.635 0.167,0.177 10 false *3 0.396,1.76 0.573,1.927 0.177,0.167 10 false *a 0.76,2.094 0.948,2.24 0.188,0.146 10 false *5 1.969,2.906 2.177,3.063 0.208,0.156 10 false D- 1.083,2.896 1.323,3.052 0.24,0.156 10 false D+ 0.708,2.354 0.969,2.531 0.26,0.177 10 false F17

Disconnect the instrument panel wire from the spiral cable sub-assembly.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-1 (D+) - Body ground Ignition switch ON Below 1 V
F17-2 (D-) - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-1 (D+) - F17-2 (D-) Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-1 (D+) - Body ground Always 1 MΩ or higher
F17-2 (D-) - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-1 (D+) - F17-2 (D-) Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Text in Illustration
*1 Steering Pad (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*5 Connector C
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


OK

6.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
U158389E02
1.792,2.344 1.427,2.604 true 2.323,2.563 1.969,2.333 true 0.479,0.406 0.323,0.917 false 2.031,0.896 1.896,0.479 false 1.094,1.854 1.25,2 0.156,0.146 10 false *5 1.208,2.542 1.406,2.698 0.198,0.156 10 false D- 2.292,2.573 2.49,2.729 0.198,0.156 10 false D+ 0.406,1.729 0.563,1.875 0.156,0.146 10 false *a 0.396,1.135 0.5,1.292 0.104,0.156 10 false F 0.583,1.135 0.708,1.292 0.125,0.156 10 false E 1.573,1.125 1.698,1.281 0.125,0.156 10 false D 1.75,1.125 1.875,1.281 0.125,0.156 10 false C 2.135,1.125 2.26,1.281 0.125,0.156 10 false B 2.469,0.865 2.594,1.021 0.125,0.156 10 false A 0.813,1.344 0.969,1.49 0.156,0.146 10 false *2 0.51,0.323 0.656,0.469 0.146,0.146 10 false *1 1.698,0.375 1.854,0.51 0.156,0.135 10 false *4 2.344,1.417 2.5,1.573 0.156,0.156 10 false *3 1.094,2.104 1.292,2.26 0.198,0.156 10 false z1

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z1-2 (D+) - Body ground Ignition switch ON Below 1 V
z1-1 (D-) - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - Body ground Always 1 MΩ or higher
z1-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the original condition.


Text in Illustration
*1 Steering Pad (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag Sensor Assembly
*4 Instrument Panel Wire
*5 Connector E
*a Front view of wire harness connector
(to Steering Pad (Driver Side Squib))


OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY