Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the airbag sensor assembly and front seat side airbag assembly RH.

This circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1820/55
·

The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary check.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Airbag sensor assembly


B1821/55
·

The airbag sensor assembly receives an open circuit signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


B1822/55
·

The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction


B1823/55
·

The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C222225E14
4.605,4.843 6.159,5.012 1.554,0.169 10 Airbag Sensor Assembly 1.05,3.701 3.355,4.030 2.304,0.329 10 Front Seat Side Airbag Assembly RH (Side Squib RH) 1.05,3.533 1.321,3.677 0.270,0.144 10 K30 4.456,2.115 4.563,2.266 0.107,0.151 10 8 4.456,2.944 4.551,3.089 0.095,0.145 10 7 2.76,2.118 2.863,2.262 0.103,0.144 10 1 2.76,2.941 2.858,3.092 0.098,0.151 10 2 4.605,4.676 4.881,4.827 0.276,0.151 10 K32 4.704,2.208 5.084,2.349 0.380,0.141 10 SFR+ 4.704,3.044 5.049,3.184 0.345,0.140 10 SFR- 2.266,2.121 2.654,2.260 0.387,0.139 10 SFR+ 2.266,2.943 2.625,3.090 0.359,0.147 10 SFR-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C165140E66
0.844,1.833 0.844,2.417 false 1.208,0.802 1.448,1.698 false 1.063,0.667 1.292,0.833 0.229,0.167 10 false *3 0.771,2.438 0.958,2.615 0.188,0.177 10 false *1 2.115,2.104 2.302,2.271 0.188,0.167 10 false *2 1.885,1.667 2,1.813 0.115,0.146 10 false A 1.552,1.906 1.667,2.052 0.115,0.146 10 false B 1.167,1.917 1.281,2.063 0.115,0.146 10 false C 0.958,1.927 1.073,2.073 0.115,0.146 10 false D

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat side airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat side airbag assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Side Airbag Assembly RH (Side Squib RH)
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH (SIDE SQUIB RH)
SST
09843-18061  

a.
U158381E02
2.5,2.698 2.729,2.698 false 0.948,0.969 1.125,0.583 false 1.156,0.49 1.323,0.656 0.167,0.167 10 false *1 1.667,1.229 1.833,1.406 0.167,0.177 10 false *2 1.052,1.167 1.167,1.323 0.115,0.156 10 false D 1.25,1.167 1.385,1.333 0.135,0.167 10 false C 0.885,1.604 1.073,1.771 0.188,0.167 10 false *a 1.177,1.948 1.365,2.115 0.188,0.167 10 false *3 2.781,2.615 3.094,2.76 0.313,0.146 10 false SST 1.125,2.24 1.438,2.417 0.313,0.177 10 false K30

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Side Airbag Assembly RH (Side Squib RH)
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly RH (Side Squib RH))



OK

NG

3.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
3.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
a.
U158382E01
0.958,1.252 1.079,1.405 0.121,0.153 10 D 1.166,1.252 1.286,1.405 0.121,0.153 10 C 1.553,1.252 1.673,1.405 0.121,0.153 10 B 1.903,1.016 2.023,1.169 0.121,0.153 10 A 0.954,0.439 1.120,0.598 0.166,0.159 10 *1 1.503,0.438 1.685,0.599 0.182,0.162 10 *3 2.134,1.34 2.330,1.523 0.196,0.183 10 *2 1.397,1.835 1.573,1.986 0.176,0.151 10 *4 1.45,2.72 1.836,2.878 0.386,0.158 10 SFR+ 2.537,2.72 2.907,2.878 0.370,0.158 10 SFR- 1.345,2.123 1.646,2.280 0.301,0.158 10 K30 2.121,2.484 1.954,2.792 false 0.887,1.639 1.102,1.803 0.215,0.164 10 *a 1.411,1.024 1.465,0.517 false 0.856,1.024 0.911,0.517 false 2.307,2.484 2.475,2.792 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the floor wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K30-1 (SFR+) - Body ground Ignition switch ON Below 1 V
K30-2 (SFR-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K30-1 (SFR+) - K30-2 (SFR-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K30-1 (SFR+) - Body ground Always 1 MΩ or higher
K30-2 (SFR-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K30-1 (SFR+) - K30-2 (SFR-) Always 1 MΩ or higher


Text in Illustration
*1 Front Seat Side Airbag Assembly RH (Side Squib RH)
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Side Airbag Assembly RH (Side Squib RH))




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat side airbag assembly RH and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.




OK

NG