Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › 2014.07–2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag sensor assembly and front seat outer belt assembly RH.

This circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1900/73
·

The airbag sensor assembly receives a line short circuit signal in the front pretensioner squib RH circuit during primary check.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag sensor assembly


B1901/73
·

The airbag sensor assembly receives an open circuit signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


B1902/73
·

The airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction


B1903/73
·

The airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C222225E18
4.603,4.853 6.145,5.003 1.542,0.150 10 Airbag Sensor Assembly 1.05,3.726 3.276,4.049 2.226,0.322 10 Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 1.05,3.558 1.342,3.719 0.291,0.160 10 K26 4.428,2.138 4.537,2.278 0.109,0.139 10 4 4.433,2.987 4.533,3.129 0.099,0.142 10 3 2.718,2.136 2.825,2.280 0.107,0.144 10 1 2.718,2.984 2.820,3.132 0.103,0.148 10 2 4.603,4.694 4.876,4.840 0.273,0.145 10 K32 4.704,2.219 5.011,2.364 0.308,0.145 10 PR+ 4.704,3.055 4.979,3.196 0.275,0.140 10 PR- 2.378,2.135 2.585,2.280 0.207,0.145 10 R+ 2.378,2.985 2.562,3.130 0.184,0.145 10 R-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C165140E65
0.833,1.833 0.833,2.417 false 1.208,0.792 1.448,1.688 false 1.031,0.708 1.26,0.875 0.229,0.167 10 false *3 0.781,2.448 0.969,2.625 0.188,0.177 10 false *1 1.75,1.969 1.938,2.135 0.188,0.167 10 false *2 1.875,1.667 1.99,1.813 0.115,0.146 10 false A 1.542,1.906 1.656,2.052 0.115,0.146 10 false B 1.156,1.906 1.271,2.052 0.115,0.146 10 false C 0.948,1.906 1.063,2.052 0.115,0.146 10 false D

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2 Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
SST
09843-18061  

a.
U158392E02
2.604,2.25 2.792,2.25 false 0.906,1.094 0.906,1.458 false 1.031,1.156 1.156,1.313 0.125,0.156 10 false D 1.229,1.156 1.354,1.313 0.125,0.156 10 false C 0.833,1.49 1,1.635 0.167,0.146 10 false *1 1.625,1.198 1.823,1.375 0.198,0.177 10 false *2 1.021,1.781 1.198,1.948 0.177,0.167 10 false *a 1.271,2.156 1.448,2.323 0.177,0.167 10 false *3 2.833,2.167 3.125,2.323 0.292,0.156 10 false SST 1.24,2.448 1.5,2.625 0.26,0.177 10 false K26

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


Text in Illustration
*1 Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))

HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
3.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
U158393E01
1.562,2.672 1.772,2.825 0.211,0.154 10 R+ 2.661,2.669 2.875,2.822 0.214,0.154 10 R- 0.951,1.211 1.072,1.363 0.121,0.153 10 D 1.155,1.211 1.275,1.363 0.121,0.153 10 C 0.765,1.451 0.924,1.594 0.159,0.143 10 *1 1.772,1.251 1.942,1.412 0.169,0.161 10 *2 0.658,1.829 0.816,1.991 0.158,0.162 10 *a 1.128,2.093 1.291,2.245 0.163,0.151 10 *4 0.846,1.149 0.846,1.438 false 1.55,1.211 1.670,1.363 0.121,0.153 10 B 1.899,0.988 2.020,1.140 0.121,0.153 10 A 2.127,2.384 1.806,2.754 false 2.307,2.389 2.617,2.749 false 1.035,0.361 1.260,0.531 0.225,0.170 10 *3 1.256,0.439 1.402,0.997 false 1.066,2.377 1.330,2.559 0.264,0.181 10 K26

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the floor wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K26-1 (R+) - Body ground Ignition switch ON Below 1 V
K26-2 (R-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-1 (R+) - K26-2 (R-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-1 (R+) - Body ground Always 1 MΩ or higher
K26-2 (R-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-1 (R+) - K26-2 (R-) Always 1 MΩ or higher


Text in Illustration
*1 Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.




OK

NG