Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o VSC) › 2011.08–2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248315 AIRBAG SYSTEM(w/o VSC) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o VSC)  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS condition is normal, the SRS warning light illuminates for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light illuminates or blinks to inform the driver of the problem. When terminals TC and CG of the DLC3 are connected, the SRS warning light blinks to indicate DTCs.

The airbag sensor assembly is equipped with a voltage-increase circuit (DC-DC converter) in case the source voltage decreases. When the battery voltage decreases, the voltage-increase circuit (DC-DC converter) boosts the SRS voltage up to the normal level.

Malfunctions relating to battery voltage decreases cause the SRS warning light to illuminate. However, no DTCs are recorded in the airbag sensor assembly. The SRS warning light goes off automatically when the source voltage returns to normal.

Signals to illuminate the SRS warning light are transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C243185E02
0.782,5.405 2.655,5.582 1.873,0.177 10 CAN Communication Line 2.872,2.246 3.091,2.393 0.219,0.148 10 39 2.872,2.841 3.133,2.987 0.261,0.146 10 40 2.872,3.425 3.065,3.576 0.193,0.151 10 21 3.132,2.345 3.427,2.528 0.295,0.184 10 IG+ 3.132,2.942 3.327,3.139 0.195,0.198 10 B 3.132,3.522 3.462,3.726 0.330,0.205 10 ET 3.609,1.757 4.042,1.899 0.434,0.142 10 CANL 3.602,2.347 4.035,2.510 0.434,0.163 10 CANH 6.149,1.743 6.583,1.885 0.434,0.142 10 CANL 6.149,2.338 6.583,2.501 0.434,0.163 10 CANH 4.096,1.591 4.345,1.739 0.249,0.148 10 31 4.095,2.193 4.328,2.338 0.232,0.144 10 32 5.871,1.591 6.132,1.781 0.260,0.191 10 22 5.871,2.193 6.111,2.377 0.239,0.184 10 13 5.864,3.249 6.076,3.453 0.211,0.205 10 25 5.871,3.841 6.097,4.031 0.225,0.191 10 26 6.149,3.347 6.361,3.503 0.211,0.156 10 E1 6.149,3.949 6.389,4.119 0.239,0.170 10 E2 5.879,0.444 6.058,0.596 0.179,0.151 10 21 6.149,0.535 6.500,0.696 0.350,0.161 10 IG2 3.097,4.765 3.485,4.949 0.387,0.184 10 F1 3.097,4.934 4.309,5.451 1.211,0.517 10 Combination Meter Assembly 5.904,4.765 6.241,4.928 0.336,0.163 10 F16 5.904,4.937 6.825,5.348 0.921,0.411 10 Airbag Sensor Assembly 0.157,0.536 1.111,0.720 0.954,0.184 10 from IG2 Fuse 0.531,2.339 1.531,2.522 1.000,0.184 10 from MET Fuse 0.027,2.929 1.766,3.224 1.739,0.295 10 from ECU-B NO. 2 Fuse

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Turn the ignition switch to ON.




OK

2.INSPECT BATTERY

NG

2.INSPECT BATTERY
a.

Measure the voltage of the battery.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V


Result
Result Proceed to
OK A
NG (for 2NZ-FE) B
NG (for 1NZ-FE) C



A

3.CHECK CONNECTION OF CONNECTORS

B

C

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF AIRBAG SENSOR ASSEMBLY)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF AIRBAG SENSOR ASSEMBLY)
a.
U158444E01
0.107,0.118 0.307,0.288 0.199,0.170 10 *a 0.578,0.998 0.850,1.179 0.272,0.181 10 F16 1.771,1.744 1.979,1.893 0.208,0.149 10 E1 1.682,1.397 1.873,1.714 false 2.201,1.744 2.409,1.893 0.208,0.149 10 E2 1.289,1.397 1.077,1.74 false 0.923,1.744 1.187,1.893 0.264,0.149 10 IG2 1.785,1.397 2.329,1.729 false

Disconnect the connectors from the airbag sensor assembly.


b.

Connect the cable to the negative battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F16-21 (IG2) -
F16-25 (E1)
Ignition switch ON 11 to 14 V
F16-21 (IG2) -
F16-26 (E2)
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Airbag Sensor Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)
a.
U158626E01
1.641,0.073 1.829,0.229 0.188,0.156 10 F1 0.521,1.224 0.4,1.644 false 0.299,1.673 0.511,1.829 0.213,0.156 10 ET 2.768,1.224 2.871,1.644 false 2.752,1.673 3.041,1.829 0.289,0.156 10 IG+ 0.2,0.098 0.413,0.254 0.213,0.156 10 *a

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Disconnect the connector from the combination meter assembly.


c.

Connect the cable to the negative battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-39 (IG+) -
F1-21 (ET)
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

6.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the combination meter assembly.


d.

Connect the cable to the negative battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

The SRS warning light goes off after the primary check period and comes on again after approximately 10 seconds.


HINT:

The primary check period lasts for approximately 6 seconds after the ignition switch is turned to ON.




OK

NG

REPLACE COMBINATION METER ASSEMBLY