Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248318 KNEE AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping a vehicle equipped with the SRS or disposing of a lower No. 1 instrument panel airbag assembly, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a lower No. 1 instrument panel airbag assembly that has an undeployed airbag.

·

The airbag emits an exploding sound when it is deployed, so perform the operation outdoors, and where it will not create a nuisance to nearby residents.

·
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the lower No. 1 instrument panel airbag assembly.

·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a lower No. 1 instrument panel airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



PROCEDURE

Hide 73900 1.DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E05
1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.73,0.645 2.89,0.831 0.161,0.186 10 *1 2.715,0.739 2.521,0.739 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery

SST
09082-00700  


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Remove the No. 1 instrument panel under cover sub-assembly.

i.

Disconnect cable from negative battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



ii.

Remove the No. 1 instrument panel under cover sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>LOWER INSTRUMENT PANEL>REMOVAL).



c.

Disconnect the airbag connector.

i.
B290209E01
1.061,2.607 1.256,2.519 false 1.262,2.443 1.421,2.587 0.159,0.144 10 *1 0.808,2.467 1.052,2.277 false 1.06,2.19 1.219,2.333 0.159,0.144 10 *2

Using a screwdriver with its tip wrapped in protective tape, release the locking button.

Text in Illustration
*1 Locking Button
*2 Protective Tape

NOTICE:

Do not damage the airbag wire harness when handling the airbag connector.



ii.

Disconnect the airbag connector.



d.
B287817E01
2.697,1.732 2.774,2.208 2.774,2.208 3.232,1.523 false 2.587,2.229 2.895,2.385 0.308,0.156 10 SST

Connect SST.

i.

Connect the SST connector to the lower No. 1 instrument panel airbag assembly.

SST
09082-00700  
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
B286373E01
1.168,0.68 1.537,0.456 false 1.551,0.371 1.733,0.539 0.182,0.168 10 *1

Push in the locking button.

Text in Illustration
*1 Locking Button

NOTICE:
·

Securely lock the locking button.




iii.
U134481E03
1.01,1.854 2.49,1.854 false 2.625,1.042 2.625,1.917 false 0.875,1.792 0.875,1.917 false 1.719,0.844 2.146,0.219 false 0.719,1.5 0.375,1.26 false 2.177,0.104 2.354,0.281 0.177,0.177 10 false *1 0.073,1.135 0.458,1.333 0.385,0.198 10 false SST 1.208,1.875 2.156,2.073 0.948,0.198 10 false 10 m or more

Move SST to at least 10 m (33 ft.) away from the vehicle.

Text in Illustration
*1 Battery


iv.

Close all doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.



v.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.



e.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

Make sure that no one is near the vehicle when deploying the airbag.

·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly which has been deployed.

·

Do not apply water, etc. to a lower No. 1 instrument panel airbag assembly which has been deployed.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.




Hide 73900 2.DISPOSE OF LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (When not Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E05
1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.73,0.645 2.89,0.831 0.161,0.186 10 *1 2.715,0.739 2.521,0.739 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Remove the lower No. 1 instrument panel airbag assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Before removing the lower No. 1 instrument panel airbag assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the lower No. 1 instrument panel airbag assembly, keep the upper surface of the airbag deployment side facing upward.




c.
B445422E01
1.719,1.635 1.99,1.219 false 1.563,1.573 1.792,1.802 0.229,0.229 10 false *a 2.865,0.969 3.052,1.198 0.188,0.229 10 false A

Using a braided wire harness, tie the lower No. 1 instrument panel airbag assembly to the tire.

Text in Illustration
*a Stripped Wire Harness Section

Stripped wire harness section:
Area Measurement
A 1.25 mm2 or more (0.00192 in.2 or more)


CAUTION:

Do not use a wire harness that is too thin or any other object to tie the lower No. 1 instrument panel airbag assembly because it may snap due to the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire harness cross section:

Area = 3.14 x (Diameter)2 divided by 4


i.

Position the lower No. 1 instrument panel airbag assembly inside the tire, as shown in the illustration.

B287818E01
2.422,3.197 2.586,3.366 0.164,0.169 10 B 0.649,1.743 0.813,1.912 0.164,0.169 10 A

Tire size:
Area Measurement
A 360 mm (14.17 in.)
B 185 mm (7.28 in.)


CAUTION:
·

Make sure that the wire harnesses are tight. If there is any slack in the wire harnesses, the lower No. 1 instrument panel airbag assembly may become loose due to the shock when the airbag is deployed.

·

Always tie the lower No. 1 instrument panel airbag assembly with the airbag deployment side facing inside the tire.



NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.




d.

Connect SST.

i.
B282737E01
2.682,0.655 2.342,0.312 false 2.171,0.231 2.342,0.381 0.171,0.149 10 *1 2.054,2.916 1.582,2.894 false 1.247,2.8 1.561,2.964 0.314,0.164 10 SST

Connect the SST connector to the lower No. 1 instrument panel airbag assembly.

Text in Illustration
*1 Locking Button

SST
09082-00700  
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.

Push in the locking button.

NOTICE:
·

Securely lock the locking button.





e.
B282637E01
2.393,0.52 2.586,0.676 0.193,0.157 10 *1 2.398,1.405 2.592,1.561 0.193,0.157 10 *1

Place the tires.

Text in Illustration
*1 Tire (2 or more)

i.

Place at least 2 tires under the tire to which the lower No. 1 instrument panel airbag assembly is tied.


ii.

Place at least 2 tires over the tire to which the lower No. 1 instrument panel airbag assembly is tied. A disc wheel should be installed onto the top tire.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

As the disc wheel will be marked by the airbag deployment, use a waste disc wheel.

·

As the tires will be marked by the airbag deployment, use waste tires.




iii.
B105087

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.




f.
B282638E01
1.014,2.688 1.888,2.861 0.874,0.172 10 10 m or more 0.411,2.641 0.411,2.958 false 0.241,2.961 0.550,3.112 0.309,0.151 10 SST 1.396,1.59 1.559,1.739 false 1.572,1.67 1.776,1.828 0.204,0.158 10 *1

Connect SST.

Text in Illustration
*1 Battery

SST
09082-00700  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness. Also, secure some slack for SST wire harness inside the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the tire to which the lower No. 1 instrument panel airbag assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

Make sure that no one is near the tires when deploying the airbag.


HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.




h.
B287820E01
2.136,0.757 2.578,0.55 false 2.589,0.456 2.778,0.621 0.189,0.165 10 *1

Dispose of the lower No. 1 instrument panel airbag assembly.

Text in Illustration
*1 Plastic Bag

CAUTION:
·

The lower No. 1 instrument panel airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower No. 1 instrument panel airbag assembly which has been deployed.

·

Do not apply water, etc. to a lower No. 1 instrument panel airbag assembly which has been deployed.

·

Always wash your hands with water after completing the operation.



i.

Remove the lower No. 1 instrument panel airbag assembly from the tire.


ii.

Place the lower No. 1 instrument panel airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.