Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248321 CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door) N

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping a vehicle equipped with the SRS or disposing of a curtain shield airbag assembly, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.


CAUTION:
·

A airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a curtain shield airbag assembly that has an undeployed airbag.

·

The airbag emits an exploding sound when it is deployed, so perform the operation outdoors, and where it will not create a nuisance to nearby residents.

·
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the curtain shield airbag assembly.

·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a curtain shield airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



PROCEDURE

Hide 62170A 1.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E12
2.763,0.662 2.924,0.838 0.161,0.176 10 *1 1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.52,0.76 2.764,0.76 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery


ii.
B104821E01
2.309,1.679 2.647,1.88 0.338,0.201 10 SST 2.416,1.545 2.467,1.696 false

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.




c.
B282648E01
0.87,2.437 0.57,2.617 false 0.409,2.548 0.569,2.700 0.160,0.151 10 *1 1.439,2.354 1.139,2.535 false 1.438,2.261 1.597,2.412 0.160,0.151 10 *2

Using a thin-bladed screwdriver with its tip wrapped with protective tape, release the locking button.

Text in Illustration
*1 Protective Tape
*2 Locking Button

NOTICE:

Do not damage the airbag wire harness when handling the airbag connector.



d.

Disconnect the airbag connector.


e.
B282652E01
1.003,1.849 1.25,1.848 false 1.257,1.764 1.587,1.933 0.330,0.169 10 SST

Connect SST.

SST
09082-00700  
09082-00802  (09082-10801, 09082-20801)

i.

After connecting SST, connect it to the curtain shield airbag assembly.

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.

Push in the locking button.


iii.
U134481E03
1.01,1.854 2.49,1.854 false 2.625,1.042 2.625,1.917 false 0.875,1.792 0.875,1.917 false 1.719,0.844 2.146,0.219 false 0.719,1.5 0.375,1.26 false 2.177,0.104 2.354,0.281 0.177,0.177 10 false *1 0.073,1.135 0.458,1.333 0.385,0.198 10 false SST 1.208,1.875 2.156,2.073 0.948,0.198 10 false 10 m or more

Move SST to at least 10 m (33 ft.) away from the vehicle.

Text in Illustration
*1 Battery


iv.

Close all doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.



v.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.



f.

Deploy the curtain shield airbag assembly.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the curtain shield airbag assembly.

CAUTION:
·

When deploying the curtain shield airbag assembly, make sure that no one is near the vehicle.

·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.

·

Do not apply water etc. to a curtain shield airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.




Hide 62170A 2.DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When not Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E12
2.763,0.662 2.924,0.838 0.161,0.176 10 *1 1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.52,0.76 2.764,0.76 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery


ii.
B104821E01
2.309,1.679 2.647,1.88 0.338,0.201 10 SST 2.416,1.545 2.467,1.696 false

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.




c.
B272968E01
1.613,1.383 1.175,1.946 false 1.065,1.946 1.234,2.105 0.169,0.159 10 *a

Cut off the deployment section of the curtain shield airbag assembly.

Text in Illustration
*a Cut


d.
B272970

Using a T25 "TORX" socket wrench, remove the screw.


e.
B286375E03
0.771,3.021 1.458,3.271 1.458,3.271 1.323,2.938 false 2.354,0.688 2.073,0.469 false 1.49,3.198 1.802,3.365 0.313,0.167 10 false SST 1.906,0.365 2.125,0.563 0.219,0.198 10 false *1

Connect SST.

Text in Illustration
*1 Locking Button

SST
09082-00802  (09082-10801, 09082-20801)

i.

After connecting SST, connect it to the curtain shield airbag assembly.

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.

Push in the locking button.



f.
B445426E01
1.552,1.667 1.854,1.208 false 1.365,1.563 1.563,1.74 0.198,0.177 10 false *a 2.844,0.969 3.042,1.146 0.198,0.177 10 false A

Using a braided wire harness, tie the curtain shield airbag assembly to the tire.

Text in Illustration
*a Stripped Wire Harness Section

Stripped wire harness section:
Area Measurement
A 1.25 mm2 or more (0.00192 in.2 or more)


CAUTION:

Do not use a wire harness that is too thin or any other object to tie the curtain shield airbag assembly because it may snap due to the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross section of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire harness cross section:

Area = 3.14 x (Diameter)2 divided by 4


i.
B286376E02
1.951,0.847 2.079,1.007 0.128,0.161 10 A 1.584,2.371 1.712,2.531 0.128,0.161 10 B

Position the curtain shield airbag assembly inside the tire, as shown in the illustration.

Tire size:
Area Measurement
A 185 mm (7.28 in.)
B 360 mm (14.17 in.)


CAUTION:

Make sure that the wire harnesses are tight. If there is any slack in the wire harnesses, the curtain shield airbag assembly may become loose due to the shock when the airbag is deployed.


NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.




g.
C121167E02
2.061,1.437 2.246,1.64 0.185,0.203 10 *1 2.061,0.332 2.278,0.534 0.216,0.203 10 *1

Place the tires.

Text in Illustration
*1 Tire (2 or more)

CAUTION:

Do not place the curtain shield airbag assembly with the deployment direction facing toward the ground.


i.

Place at least 2 tires under the tire to which the curtain shield airbag assembly is tied.


ii.

Place at least 2 tires over the tire to which the curtain shield airbag assembly is tied. The disc wheel should be installed onto the top tire.

NOTICE:
·

Do not place SST connector under the tire because it could be damaged.

·

As the disc wheel will be marked by the airbag deployment, use a waste disc wheel.

·

As the tires will be marked by the airbag deployment, use waste tires.




iii.
B105087

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. It is highly dangerous when a loose wire harness results in the tires coming free due to the shock when the airbag is deployed.




h.
C118554E07
1.597,1.483 1.754,1.653 0.157,0.170 10 *1 0.442,2.808 0.812,2.978 0.370,0.170 10 SST 1.697,2.669 2.582,2.848 0.885,0.179 10 10 m or more 1.407,1.583 1.597,1.583 false 0.627,2.673 0.627,2.808 false

Connect SST.

Text in Illustration
*1 Battery

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



i.

Deploy the curtain shield airbag assembly.

i.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the tire to which the curtain shield airbag assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

Make sure that no one is near the tire when deploying the airbag.


HINT:

The airbag is deployed as the LED on the SST activation switch illuminates.




j.
B108351E02
0.832,0.613 1.016,0.776 0.184,0.163 10 *1 1.209,0.937 1.014,0.719 false

Dispose of the curtain shield airbag assembly.

Text in Illustration
*1 Plastic Bag

CAUTION:
·

The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a curtain shield airbag assembly which has been deployed.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a curtain shield airbag assembly which has been deployed.



i.

Remove the curtain shield airbag assembly from the tire.


ii.

Place the curtain shield airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.