The circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) is composed of the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
The door side airbag sensor RH and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
DTC B1692/81 and B1693/81 are recorded when a malfunction is detected in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1692/81
B1693/81 |
When one of following conditions is met:
·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) for 2 seconds. ·
Door side airbag sensor RH malfunction ·
No. 2 side airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Door side airbag sensor RH ·
No. 2 side airbag sensor assembly RH ·
Airbag sensor assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
The connectors are properly connected
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
Check that the terminals of connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector B | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - K46-2 (BDR-) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - K46-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| K46-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| K46-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692/81 or B1693/81 is output. | A |
| DTC B1697/82 or B1698/82 is output. | B |
| DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.
A
B
C
Interchange the door side airbag sensor RH with the door side airbag sensor LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692/81, B1693/81, B1697/82 and B1698/82 are not output. | A |
| DTC B1692/81 or B1693/81 is output. | B |
| DTC B1697/82 or B1698/82 is output. | C |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
Codes other than DTCs B1692/81, B1693/81, B1697/82 and B1698/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.
A
B
C
Disconnect the floor wire connector from the front door wire RH.
| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector D | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Floor Wire) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
The service wire has already been inserted into connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | Below 1 Ω |
OK
NG
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the front door wire RH connector from the floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| GK2-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Disconnect the front door wire RH connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| GK2-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG